Recent content by deanj
-
D
easyiest way to replace return lines ?
The best way is to remove each bank as an assembly, make the new one up on the bench and then replace. Make sure you undo all the injector lines and then move just enough to remove the 'top hats', do not bend if you can help it. Us a lube on the "O" rings ( I use some petrolium jelly ). The...- deanj
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
Tranny Temp and Battery question...
As for trans temp, keep it below 200. Install a plate type cooler around 20k rating. First where are you measuring the temp?- deanj
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
torque converter
At the least you want a RV converter. Look around the summit racing site, or do a search. Basically get the best you can afford as they are a weak link if you are towing. When changing do not forget to flush out your coolers.- deanj
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
Belt took out tranny cooler lines!
Welcome to the club, been thier done that (the worst is that I had a new belt in the cab - to lazy to replace) You can go to your local harware store and get compression fittings (5/16 I think) with a pipe thread on the other end, then a 5/16 barb fitting (with the appropriate thread) then use...- deanj
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
Factory wastegate adjust and pyro probe
Sounds like the rod is screwed in to far = maxed. Go to your friendly local dealer and see if you can measure a stock one. Is the diafram ok? As for the pyro why not put it in the exhaust manifold opposite the exhaust port? This will give you the most accurate reading (unless it is a post turbo...- deanj
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
tranny to the shop 4EOD
Do not forget to get a trans temp. Who ever is going to do the install make sure they clean out the trans lines and cooler. The set up I have on the 94, is the trans cooler (plate design 20k) and fan are mounted in the front bumper. On the supply line ( to the cooler - line nearest the bell...- deanj
- Post #11
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
ats exhaust
If you go by diesel fundermentals MORE AIR IN - MORE EXHAUST OUT then look at the downpipe you will see that it is worth it. The stock d/pipe is 2 1/4 dia that has been run over by a fork lift - in other words really restrictive. Get the turbo outlet and 3 inch down pipe, then a 4 inch exhaust...- deanj
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
tranny to the shop 4EOD
Do not put a reman ford trans in unless they have done all the up grades, thier are a whole bunch of them. Talk to your local trans shop, thier are bearings, cluth packs , code 62 pump kits , different bearings --- the list goes on. For the T/C get the best one you can afford (do a search) , at...- deanj
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
Anyone ever try H.I.D. Headlights?
Do the relay mod first, the stock wiring is to smaller guage.- deanj
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
94 idi turbo exhuast
Forgot to add, their are a lot of opinions on when you need the intercooler, my opinion is that if your egt's are not to high don't bother.- deanj
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
94 idi turbo exhuast
Their are several outfits that make just the down pipe, it replaceses the stock (run over by a fork lift) down pipe but you stil have the 2.25 out let. The ats huosing and 3 inch down pipe is the way to go, after that get a 4 inch exhaust (for a 94.1/2 power choke - bullydog i think still has...- deanj
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
E4OD in limp mode - will driving it cause damage ?
Try not to drive, T/C replacement can get expensive.- deanj
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
Cowl induction hood for ATS turbo
Go to their web site. On one 94 I have the hypermax "cowl induction", have not had any problems untill it sat over night in the rain. My drains were plugged and the valley was half full with water - lucky I pulled the inlet tube and some water came out - cleaned out the drains, had no problems...- deanj
- Post #12
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D
Cowl induction hood for ATS turbo
Have you looked at their web site? They take the air from the space between the windshield and the engine compartment. You cut a 2 x 5 hole in the firewall, screw the hypermax snorkel to the firewall and connect to your intake. you are taking the high pressure air created by the windshield. Make...- deanj
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
Latest posts
-
Supply fuel line from fuel filter housing to injection pump- Latest: SkylabTech86IDI
-
-
-
