Search results

  1. Duke57

    f350 cab and chassis Ujoints

    Need ujoints again. Have the choice between spicer and moog. Replaced all three on the driveshaft 2 years ago and they're starting to squeak again. My work truck, use every day. 92 F350 cab and chassis, zf5. Any suggestions. Thanks. Mike
  2. Duke57

    Factory manuals from TorqueKing4X4

    I am about to buy the CD factory manual from TorqueKing 4X4. Has anyone bought this cd from them?
  3. Duke57

    New R&D injectors

    I finally swapped out the old injectors on 92 IDI with Justins injectors. Truck had been running rough, smoking and putrid smell for months. Some injectors had no copper washers and one had 2 of them. Took my time, clean out the injector cavity (or whatever you call it), they were really gummed...
  4. Duke57

    7.3 NA running as if it had a bad spark plug wire or bad plug.

    Engine is running rough as if it had a bad spark plug wire or plug. All injectors are receiving fuel. there are times when the miss stops and engine runs smooth. When I crank up engine, hot or cold, always cranks up in 1/2 second. Old engine though. I posted pictures of one of the rocker arms...
  5. Duke57

    Carquest Fuel filter

    I am now sold on carquest fuel filters. Been using them for 3 years but never opened one up. This filter isn't a year old and it looks dirty but the inside of my tank is clean. This was the filter that you don't need the bottom screw on part but went back to the old style filter this...
  6. Duke57

    Tapping Noise

    I have a sharp tapping noise in my IDI. Will try to attach a sound file. Has anyone ever heard of this sound in your IDI? Most pronounced when cold as I just started and it is starting to go away. 1992 F350 cab and chassis flatbed Custom 5 speed Been driving this for 3 years solid every...
  7. Duke57

    Leaking injector line

    I have an injector line that started to spray out of the compression nut that secures the line to the injector. Do these lines develope hairline cracks near the flare? Cannot stop the spraying . Where is the best/most affordable place to buy a new one? My injector lines do not...
  8. Duke57

    V-belt A/C compressor bracket installed pics.

    Since my cab of my truck stays around 101+ for the last 4 months down here in FL, I am going to do a compressor install and get my AC running. Got the bracket and old compressor from previous owner and would like to ask if anyone has some pics of that style compressor installed. Thanks
  9. Duke57

    Faint high pitch sound from IP

    What does it mean, if you have a high pitch sound, not very loud, coming from your injector pump?
  10. Duke57

    2001 7.3 PSD 90k rebuilt by Caterpillar for trade or sale

    friend of mine did the cummins conversion, turned out great! I ended up with his 2001 rebuilt 7.3 psd engine less the alternator. What I would like to do with it is trade it for a fairly young 7.3 turbo idi w/a decent zf5 trans. Duke ps also have a 96 F450 cab and chassis straight axle,14ft...
  11. Duke57

    Better acceleration cold than warm!

    I have a 92 F350 NA that when warming up driving has a more normal acceleration than after it warms up. After it warms up it is more like "don't push me, I'm getting there"! I know that when cold the IP is advanced a little but after it warms up, well, more like an old hound dog that's ready to...
  12. Duke57

    Tach moving backwards when engine reaches 1800 rpm

    I noticed a few months ago when on the interstate the the tach was acting funny when driving about 60 to 65 mph. The tach-o-meter when accelerating would approach 1800 rpm then actually move backwards to 1500 rpm. I attributed it to the old rpm engine sensor and figured all this erratic...
  13. Duke57

    7.3 IDI transmission clutch diameter

    I have to drop transmission this week to replace friction plate, pressure plate and throw out bearing. So have a few questions for my fellow oil burners. 1. Advanced auto is asking me what diameter clutch plate. 11 inch or 12? Were there 2 sizes? 2. I have that chirp and shaking release lever...
  14. Duke57

    Zf5 cross reference between IDI and psd.

    Will a 7.3 powerstroke zf5 fit on a 7.3 IDI?
  15. Duke57

    Zf5

    Planning to pull 5sp zf5 for rebuild. Need advice on getting rid of the high gear reverse.
  16. Duke57

    power steering pump alignment

    Replaced my power steering pump on my 92 F350 but pulley not aligned. I need to choose washers to align pump to pump bracket. Any others out there ever have this problem? Did a search on forums for 'power steering alignment', but no results. So I started thread with a title that would help...
  17. Duke57

    power steering pump alignment

    Replaced my power steering pump on my 92 F350 but pulley not aligned. I need to choose washers to align pump to pump bracket. Any others out there ever have this problem? Did a search on forums for 'power steering alignment', but no results. So I started thread with a title that would help...
  18. Duke57

    What is this folks?

    I should trace out the wire but doing to many others things to bring up the maintenance on this 92 F350 dually a friend of mine gave me.
  19. Duke57

    just joined

    I have read articles on this forum for a long time and decided to join. Mike 98 e350 7.3 96 f450 7.3 Newest and best truck: 92 and 3/4 F350 7.3 IDI 5 SPEED flatbed

Latest posts

Forum statistics

Threads
91,324
Posts
1,130,370
Members
24,131
Latest member
JFMac

Members online

Total: 430 (members: 7, guests: 423)

Share this page

Top