Hey alls... figured I'd share here too.
I'm currently collaborating with WVO Designs and they've given me a discount code to share with viewers of my YT channel. They typically don't discount their products... I think this is a first for them.
With that said, check the video description for...
Hey alls,
Just posted the final review video on the 55gph centrifuge from PA Biodiesel and the giveaway is live. Watch the video... follow the instructions. No cost (assuming you are in the lower 48)... no nonsense.
Thanks to PA Biodiesel Supply for helping put this together.
Hey guys...
Just posted the first video on the PA Biodiesel 55gph unit. This is how you setup their (or any other) pressure driven centrifuge.
I also give a few details on the giveaway that's starting next week. The 55gph unit I'm currently testing will be up for grabs.
Thanks!
Hey guys...
So put together a couple videos highlighting the differences.. pros and cons of both single and dual tank setups for WMO.
I run a single tank currently in my 300SD running 50/50 W90 to diesel... And dual tanks in my IDI.. straight W90 in the auxiliary tank.
Both work...
Good morning alls...
So this is why I prefer a centrifuge. Over the last 10 years, I've used about every method to get our oil clean. Nothing compares to a single pass so far.
Hey guys...
Just bought a big bus for our toy hauler conversion. Our little bus (7.3 IDI) drinks WMO no problem... so was curious how the DT would handle it.
Anyone have experience with it?
Hey guys...
Well.. I'm almost 100% certain that I did not have a speedo cable hooked to my cluster when I removed it last... however the speedo is driven via a cable off the transfer case.
Am I not remembering correctly or does it have some sort of mechanical/electrical signal generator?
If...
Anyone know where I can find an all aluminum radiator for a '93 E350?
I can find them for the older body style.. and the 95+.....
Could have one custom made as PRC is just a few miles from the house... but that would be costly and would like to avoid that if I can.
Thanks
Hey guys...
I was in need of a fan clutch so started looking around...
Just ordered one for my '90 F350.. Motorcraft YB467
$67 shipped.
Just figured I'd give a heads up as that's CHEAP.
I compared the Hayden part numbers for 1990 and 1993 (my engine is a '93). Hayden uses the same clutch...
Hey guys..
Anyone have specifics on how the parking brake is supposed to be set?
Everything is new in the rear including brake cables. Brakes feel good but the parking brakes do nothing. The rear cables move the shoes... so I must not have them adjusted right. With the pedal released...
Hey guys...
So I have my 10.25 at the local drivetrain shop getting re-geared. I supplied the gears (Dana SVL 4.88) and install kit (National).
The pinion that came out of my housing didn't have any sort of lip under the pinion head (between the bearing surface and pinion head).. however the...
Hey guys...
Looking for a full aluminum radiator for a '93 E350.
I got an E350 based bus given to me and am planning on going over things with a fine tooth comb as it has several multi-thousand mile trips in it's future (as an adventure rig).
So.. right now it has a replacement plastic tank...
Hey guys...
So I was looking around for a higher output alternator to upgrade mine and wasn't having much luck (other then spending $600 or so from DC).
Looking around on Rockauto... I found that the 93 idi and 95 powerstroke share alternators... Part nummbers match up on several of them...
Hey guys..
So ever since I bought my truck, the door glass on the driver's side fits loose and can come out of the track. I assume its because the rubber that fits in the track is gone.
Is that all that keeps the glass on track is the rubber seal? Getting ready to fix both sides and need to...
In the process of rebuilding my AC system top to bottom...
The new pressure hose assembly that bolts to the compressor has 2 inline canisters (one on each line).. roughly 1.5" diameter/3" long. Are these some sort of filter? The original hoses don't have them.
Hey guys..
So my plans for my '90 F350 have changed and now my wife and I are planning on building a part time expedition rig out of it. We will be starting on building the camper soon (it will be a lift off cab over type that will be mounted to the flatbed and can be removed easily when not...
Hey guys..
So.. 2 nearly identical trucks.. only difference is rear gear (4.10 vs 3.55). Same 37" rubber... same trans... same clutch kit (luk single mass conversion).
The truck with 3.55s has no problem resting on a grade in gear without using the parking brake. Mine however, will...
Hey guys..
Well I thought I had a blend door actuator issue... so I removed the actuator to find that the blend door itself seems to be broken/damaged.
I haven't pulled the box yet to see what I'm dealing with... but where am I going to find a new blend door if it is broken?
From my...
Hey guys...
So my '90 F350 came to me missing most of the AC components. I have since swapped to a '93 engine with serpentine setup... ordered new hoses, condenser, evap, drier, orifice tube, etc.. all new. Only thing that may get reused is the compressor that is on the engine now... not...
Hey guys...
Just wondering what you waste oil guys do for long distance runs (1500 mile+)?
I've been tossing around the idea of a fuel trailer... or a LARGE tank on the truck (100+ gallon).
Ideas?
Hey guys...
Those of you running bypass filters, how large of an orifice does your filter head or restrictor fitting use? The filter head I'll be using doesn't have a restrictor and I don't want to be limited to certain filters.
The filter I'm using for now (or will be once plumbed) is a...
Hey guys..
Well I'm trying to decide on getting an auxiliary underdrive unit or taking off in low range when pulling heavy loads. Truck has 4.10s and 37" rubber and I don't want to have to slip the clutch to get it moving when heavy.
I'd heard several people talk about taking off in 4 low and...
Hey guys...
Has anyone heard from or talked to the guy that runs Terrapin lately? I've attempted to contact him several times and haven't had any luck.
I ordered a plate a few weeks back and never heard anything after paying for it. I'm aware he's a one man show and what have you.. so I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.