Search results

  1. nelstomlinson

    Charging question

    Insulated wrenches. https://legionsafety.com/p/1861-knipex-insulated-open-end-wrench-tool-set-98-99-13-s5/v/18114 Or, tape some pawn shop wrenches with plenty of electrical tape.
  2. nelstomlinson

    Well, Fu-udge.

    If you could deliver that ladder truck to Fairbanks, I'd be tempted. That's totally unrealistic, so I guess I'm safe from getting another project.
  3. nelstomlinson

    Spindle Nut Socket Size?

    Since it's Easter, I guess it's appropriate to resurrect a thread? Here's another. OTC Part Number 7158 https://www.otctools.com/products/locknut-socket-1
  4. nelstomlinson

    Arctic Ambulance

    The e4od intermittently starts flashing the OFF light and shifting hard. It'll intermittently stop flashing after while, too, but I don't like it. I unplugged the range indicator connector and the solenoid connector, hoping there was just a bit of corrosion there, but it still does it...
  5. nelstomlinson

    Changing a head gasket in the brown truck.

    For the pump filter setup, I've ordered two Wix 24764 filter heads. That should let me use the 33616 and 33281 filters before and after the pump.
  6. nelstomlinson

    Changing a head gasket in the brown truck.

    I wound up installing an after market valve. The quick connectors on the old nylon lines fell apart, so I couldn't have used an original valve anyway. That was running fine for a few minutes, then I got a few hundred feet down the road and it died, and the little Fascett pump couldn't prime it...
  7. nelstomlinson

    Electric Fuel Pump Setup - Is this no good?

    I had another mechanical pump fail in the brown truck, bypassed it and put in that Walbro FRB-13. Seems pretty solid so far, although there are some wet spots on the fuel supply line which suggest that I'm getting some air intrusion on the supply side. That would explain the occasional slight...
  8. nelstomlinson

    Charging question

    If you can measure the resistance of that red battery-to-battery cable, it's too high. I think that's what Clb was getting at. Our little 3-1/2 or 4-1/2 digit Ohm meters just can't measure micro Ohms, so if there is resistance you can measure, it's too much.
  9. nelstomlinson

    So what did you do with your truck today?

    I have an '82 MB. It's mighty nice, but I now realize German engineering is a curse. Oops, '83.
  10. nelstomlinson

    Anyone hotshot trucking in an IDI?

    Bigamist.
  11. nelstomlinson

    Changing a head gasket in the brown truck.

    I do have a few TSVs in the boneyard, I'll see if I can repair this one with a body from there.
  12. nelstomlinson

    Changing a head gasket in the brown truck.

    I got the engine back in, and it's running. Of course it wasn't quite that simple. When I was getting everything hooked up, I noticed the fuel return back to the tank selector switch wasn't quite right. I pulled, and it came off in my hand. Turns out when I pulled the engine I pulled on that...
  13. nelstomlinson

    Cup holders

    If being wrong stopped any of us, we'd never go. Also, if it weren't for bad jokes, we'd have no jokes at all.
  14. nelstomlinson

    Zd29s vs Zd9s...for the inquiring mind...

    I was thinking ether system because I saw bottles on the shelf at NAPA recently. The alternate plugs might work out. Which ones are you using?
  15. nelstomlinson

    So what did you do with your truck today?

    Goat, that says it's for GM valves? Is this what we use for our old Fords, too? Or do you have a custom setup?
  16. nelstomlinson

    Zd29s vs Zd9s...for the inquiring mind...

    I wonder if we could use a heater in the intake like a Cummins instead of the glow plugs. Or maybe an ether system. It's starting to look like glow plugs are off the table.
  17. nelstomlinson

    So what did you do with your truck today?

    I usually put a pint of power service white bottle additive into each tank with each fill up. Also a pint of Walmart 2 cycle oil, each tank each time. We can only get #1 diesel here year round. In recent years we've only had a few days where it would have gelled, but better safe than sorry...
  18. nelstomlinson

    Electric Fuel Pump Setup - Is this no good?

    My Brown Crewcab has been set up that way since before I got it. I did have a mechanical pump failure that may have leaked into the block. Fortunately I caught it before there was any obvious damage, changed the pump and the oil and carried on. Next fuel pump failure I plan to bypass the...
  19. nelstomlinson

    What is this electrical thingy on top of the engine?

    In the Brown truck the water in fuel sensor wire is hanging loose. I'll try tracing it back through the loom, see if it goes there. I should have said originally, it has four terminals, so it could be a relay.
  20. nelstomlinson

    What is this electrical thingy on top of the engine?

    I'm putting the engine for my Brown Crewcab back together, hooking up the electrical stuff on top, and noticed a little lump on the front end of the passenger side harness. This is what it looks like: This shows it plugged back in, near the #1 injector. Does anyone recognize it?
  21. nelstomlinson

    So what did you do with your truck today?

    The only day better than the day you buy your boat is the day you sell it.
  22. nelstomlinson

    So what did you do with your truck today?

    It's been a while since I looked at the sticker - maybe it's 11,000 for just the rear end? It's a decent flatbed, probably 12 feet long? That one isn't on the road, and it hasn't moved since I started it up last year to put in the new parking area. I don't look at the rigs down in the new...
  23. nelstomlinson

    So what did you do with your truck today?

    The good ol' boy who gave me the brownie had it in his hippy bread truck for years. It's an underdrive, and he'd mounted it backwards for OD. He used it to split shifts apparently. The hippy bread truck was an old diesel step van that had delivered Wonderbread for years before he got it and...
  24. nelstomlinson

    Installed Dreg's Garage's brass return caps

    I'm still very happy with the brass caps from Dregs. I wish I could get him to make me another couple of sets!
  25. nelstomlinson

    So what did you do with your truck today?

    If I go that route, the plan would be to replace the pillow block in the middle of the two part drive shaft with the brownie, one shaft running transmission to brownie, the other running brownie to differential. I'd just need to build a cross member to hold it, then have Young's Gear build me...

Latest posts

Forum statistics

Threads
93,001
Posts
1,155,992
Members
26,589
Latest member
tke395

Members online

Total: 824 (members: 2, guests: 822)

Share this page

Top