Search results

  1. 1mouse3

    A third hand for the brakes

    I got pins and a rod in right leg, using the brakes is fine but issue is using two pedals with it. I was told not to drive it like I do my gas one, where droping the throttle could spike the egts and need to back it off slowly if its high. It will also help with take off on a steep hill, where...
  2. 1mouse3

    Into the depth of the cowl...

    Well time has come again to try again at cleaning this cowl up, but at least I layed primer to cut down on clean up time. Found more body damage when cleaning... It gose with this and the bent up core supprt... Ehter way got a new coat of primer layed and got to finger...
  3. 1mouse3

    Into the depth of the cowl...

    Yea that is a issue as well but there other more important stuff on the list of stuff to do, so will be some other time. To make you feel better, they have been reduced in full to the safest place that they wont get lost.
  4. 1mouse3

    8.3 cummins fuel stopper, sparky, thingy

    I have been tring to find a favorable way, to get a cummins fuel cutoff solenoid to work every time. I was having trouble understanding the strange stuff of a plastic relay, so went up to a grid heater one. This gave me easy means to test and probe what was going on, but found magic on my path...
  5. 1mouse3

    Looking for a coolant jug/washer fluid jug for my 87 IDI

    I found this in a 90s gaser ford truck, by a battery on this side. The coolant res part might be a hair small, since was always sucked dry when running
  6. 1mouse3

    Where to buy a turbo bumper cutout insert

    This the cuts I made in my bumper to fit the vent I got from the yard... Then I drilled to mount it permanently, with washers to space it out... And this is the aftermath, I also cut out the ribs at some point so can also serve as a step.
  7. 1mouse3

    Into the depth of the cowl...

    Yea, those hold the cowl panel down. I dont think there big enogh to do anything to the tire, think found a bigger one in the tire before.
  8. 1mouse3

    Into the depth of the cowl...

    Ok, Iv cleaned this twice and did not git it done before the bad clouds pass... So another round of scrubing the phosphate acid in, then sanding in the cleaner, and followed by wipeing off with the cleaner. Well, a finger to the sky and shooting the primer anyways, after wipeing...
  9. 1mouse3

    Bla bla bla

    I feel it put me in in cahoots with the ack of pushing this tread off the cliff...
  10. 1mouse3

    Bla bla bla

    Im plumb tuckered out and a bit of a neophyte, to look into the full lexicon of the engish tongue.
  11. 1mouse3

    Into the depth of the cowl...

    I had all ready brushed it some to get some the large chunk out and treated it with acid... I found these hose picks to try some more... They do well to get the old sealent out... Some scrub pads and grease remover help with the rest... So is now cleaned up a fair bit...
  12. 1mouse3

    parallel turbos

    I put a newer jumper hose on filter contraption, since had it apart and unsure on the 10 year plus hose that was on there... Under inspection of the old, I see it still soft and the outer weave is nothing to worry about... So this old gates lock on hose will be sent again, along with...
  13. 1mouse3

    A third hand for the brakes

    I hurt my leg a long time ago and is hard for me to heal toe anymore, so finding a way around the dilemma. So old girl is getting a pair of line loks for both axles, and a used prop valve since the rabs was deleted. I have not had issues with brakes locking up under normal use, but may be from...
  14. 1mouse3

    Cup holders

    Id like her to inspect the undercarriage of my truck...
  15. 1mouse3

    Into the depth of the cowl...

    The floor pan had to be patched in this truck, and was told water can come the cowl area. I see there is signs water is still getting in, the floor mat is still rolled up. This is what I found looking in the cowl area... Here, its cleaned up some and will replace the sealer that was...
  16. 1mouse3

    Cup holders

    Give me my cuppy back
  17. 1mouse3

    Cup holders

    Duck tape and bailing wire, was the first tools and got the job done. There is a issue tho, its loose enough that my glasses have a chance to bounce off into the cup holders... This is the damage that causes thing to end up into the cup holders... I have got it fixed better, so the...
  18. 1mouse3

    Cup holders

    ;Poke Hold my cuppy of mango tea, while I try this again. ;Poke
  19. 1mouse3

    Three legged animal...

    Yea, the 4:1 mix was runny on the frame. But look at the some what decent shot of 5:1 mix shot on the axle... I do delcare, that using paper wastes time to put on but it falls off well when wet... So chiped paint is sorrted for the most part on the axle, and will see how long it last...
  20. 1mouse3

    Paint thick as molasses

    I found where the gun was leaking and set the gun back to 1.7mm tip. Also from looking around, low fluid feed or low air could had been my last issue. This is shooting the paint, a mix of hair more than 4:1 one was shoot and 5:1 off cam. The +4:1 was a bit runny and the 5:1 layed somewhat...
  21. 1mouse3

    Three legged animal...

    Finished the masking and at that point was told, could had saved time with tin foil... I have paint that might stick and hope its not too cold... The axle is dechiped for now, as well.
  22. 1mouse3

    Three legged animal...

    First off, this itch intrusive plant needs to go... So that was all riped out and safe for now... I also found this nice carpet, that might last a few days... Then started finding what wanted paint and some of what needs to hide, reduced in full to paper. The axle got a razzor...
  23. 1mouse3

    Belt driven fuel pump discussion

    Your lab rat of hoses, is impresive and that pump is a interesting choice. Also, your battery is not a good place to set metal objects.
  24. 1mouse3

    Paint thick as molasses

    Went and tried to clean the gun, then turned the paint adjustment all the way in. With what was left in the last mix, I tured it out till there was some sort of shoot. I was still getting large freckle paint job. So switched to the 1.5mm tip/needle, had to turn the paint out a fair bit and...
  25. 1mouse3

    Three legged animal...

    To pick a easy place to test the gun again, where paint wont be wasted. I chose to further repair this area that was shot two years ago, and right was a start of the repair. I forgot how stiff of shocks I got... And this is damage from this tower coming lose it the past... Then...

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,944
Members
26,577
Latest member
Jrlew87

Members online

Total: 1,394 (members: 7, guests: 1,387)

Share this page

Top