Search results

  1. Kdo58

    7.3 IDI Cranking but not catching.

    Try starting fluid, if it starts up I would look at your glow plug system
  2. Kdo58

    Changing a head gasket in the brown truck.

    You have it out and your not going to reseal the whole motor?
  3. Kdo58

    Dumb things you have done truck wise!

    No problems with rust I just kept everything oiled up, and covered up all the parts, and kept the motor covered with towels and a extra tarp, the biggest problem was pine needles.
  4. Kdo58

    Dumb things you have done truck wise!

    I rebuilt my motor in my backyard under a tarp over the winter. It has had a few leaks, since the rebuild, valve cover gaskets, front dampener, which I fixed, but it still had a leak from the oil cooler housing near the oil filter. And I had used the metal gasket, i did not know at the time...
  5. Kdo58

    Accelerator Cable replacement

    I got one from Amazon, did not fit, went to o'Reilly and it worked.
  6. Kdo58

    Classic Diesel Designs 61mm drop in replacement for a banks turbo.

    Messed with the timing, it now puts out 9lbs of boost.
  7. Kdo58

    Right front brake caliper always dragging-- ive changed everything!

    I have the same problem, I just found this video on YouTube.
  8. Kdo58

    Still need ideas 7.3 idi air intrusion

    Olive line seals
  9. Kdo58

    CDR valve replacement question

    No idea, I have a turbo on mine.
  10. Kdo58

    CDR valve replacement question

    I think the tube is used if your cdr goes into the valve cover.
  11. Kdo58

    Stubborn waterpump fan nut

    Just need the right bumper to stand on.
  12. Kdo58

    How to Replace Rear Main Seal

    On my front dampener I used a sharp wood chisel to get a old speedy sleeve off.
  13. Kdo58

    17 years later I did a compression test

    What it takes to kill a idi
  14. Kdo58

    CDR valve

    My valve covers gaskets were leaking, so I had them both off, and thought what the heck! I will just do both of them.
  15. Kdo58

    CDR valve

    I went a different route, I gutted my cdr valve and added road draft tubes to each valve cover.
  16. Kdo58

    Injector line nut leak

    Are all the injector line clamps in place?
  17. Kdo58

    Classic Diesel Designs 61mm drop in replacement for a banks turbo.

    Its a garret turbo, made to work on a banks up pipe, ccd said it would make around 7lbs of boost with a turned up stock ip. So I'm in the ball park. I can rev it to 3k. It will go higher but doesn't seam to make a difference in boost.
  18. Kdo58

    Classic Diesel Designs 61mm drop in replacement for a banks turbo.

    Turned up the factory ip I get 8lbs of boost, and exhaust temperature at full boost of 850*
  19. Kdo58

    Looking for a coolant jug/washer fluid jug for my 87 IDI

    Classic diesel designs just came out with a metal one.
  20. Kdo58

    Bla bla bla

    I got it fixed not as easy as some made it out. It has three bolts, one stuck stud broke off. To get the cable off, I had to get some slack in the cables underneath the truck, which was rusted badly and had to use some heat. The emergency brake pedal and mechanism need more them wd40 to break...
  21. Kdo58

    Need brighter reverse lights....

    LEDs are cheap, if they are not enough light then add some auxiliary lights
  22. Kdo58

    Bla bla bla

    My emergency brake pedal does not ratchet, can this be repaired or do I need to go to a wrecking yard?
  23. Kdo58

    Fuel system

    Skid plate does not protect the sump, I sure you could add some protection.
  24. Kdo58

    Fuel system

    This what I used.
  25. Kdo58

    Fuel system

    I would do a fuel sump.

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,943
Members
26,575
Latest member
Gerhard

Members online

Total: 1,640 (members: 8, guests: 1,632)

Share this page

Top