Search results

  1. Kevo1288

    Throttle cable part number?

    I used a part store one in my 92 and it was a chore to push the throttle down. Every, single, time.
  2. Kevo1288

    Project: The New CDD Shop Truck

    Ugh this makes me want to do my engine this color, same color I did the motor in my fathers 68 mustang. I do love the ford grey though!
  3. Kevo1288

    94 F-350 IDIT Build Thread

    @Thewespaul how much TA31 oil pan sealant do you recommend? Will 1 tube suffice or is 2 needed?
  4. Kevo1288

    94 F-350 IDIT Build Thread

    Pick up the new longblock with 76k miles with paperwork tomorrow, very pumped.
  5. Kevo1288

    Factory idi turbo valve covers and air box

    Sold
  6. Kevo1288

    94 F-350 IDIT Build Thread

    When the trucks back up and running this one is getting torn down and then we will find out for sure
  7. Kevo1288

    94 F-350 IDIT Build Thread

    Also these motors are not hard to prep to be pulled, I did it in about 3 hours with limited tools in my driveway, only thing left is to drain coolant and remove the turbo.
  8. Kevo1288

    94 F-350 IDIT Build Thread

    Pulled my valve covers off the Factory engine that was in my truck to sell because I am no longer going to be using them, they sold within 20 minutes. However it is very odd to see all this condensation everywhere.. I scored a sub 80k mile motor last night my buddy will be picking it up for...
  9. Kevo1288

    Factory idi turbo valve covers and air box

    200 plus the ride
  10. Kevo1288

    Rosco commercial 3 camera setup , back camera and then some....

    BUMP
  11. Kevo1288

    94 F-350 IDIT Build Thread

    Well I pulled off the intake and the turbo is mint, fins, side to side , in n out, rotates fine with pressure on the shaft in any direction.... i pulled the dipstick and found condensation today, also condensation in the cdr tube. My buddy did say he smelt coolant when we fired it up to idle on...
  12. Kevo1288

    94 F-350 IDIT Build Thread

    Also it is smoking a little, not horrendously but it is.
  13. Kevo1288

    94 F-350 IDIT Build Thread

    Ill be doing this later today, if it is a rod bearing when I pull the motor, I will probably just be throwing rod bearings at it if the crank checks out. A friend told me the rod would have to be replaced the whole 9 yards, I don't believe that. Someone change my mind?
  14. Kevo1288

    94 F-350 IDIT Build Thread

    I can tell you right now its def nkt just a gauge issue, the truck acts differently. Ill have to get a video or something this week. It def does not sound normal. I was shocked, like i never would have thought.
  15. Kevo1288

    94 F-350 IDIT Build Thread

    Dipstick is full @Thewespaul , it lost power too... im pretty sure i can hear a lower end knock from the factory intake tube. It was so sudden and it blows my mind.
  16. Kevo1288

    94 F-350 IDIT Build Thread

    And lost oil pressure on the way home. Sounds like a spun bearing, oil pressure gauge spikes from nothing to 1/2 on factory gauge and lost a lot of power. Saw the gauge as soon as it acted up coasted down the hill n shut it off in a safe spot.
  17. Kevo1288

    94 F-350 IDIT Build Thread

    Oh and i also did the doors up last weekend, along with new strikers.
  18. Kevo1288

    94 F-350 IDIT Build Thread

    Got a good amount done this weekend, would have got more done but an employee at the parts store called out so i covered today. Sound deadener on pillars and rear of cab, ill do floor and firewall when the truck gets a zf5. Also picked up my intercooler and modded my bezel with an led for low...
  19. Kevo1288

    Banks Sidewinder on an Interim 7.3 IDI

    Sounds like you've determined going with the banks unit...
  20. Kevo1288

    Can we talk suspension parts?

    Snap on tool boxes cost 60 times more than my husky, the paint sucks on them, the casters suck , but they still cost more.
  21. Kevo1288

    Banks Sidewinder on an Interim 7.3 IDI

    Factory kit is easier to upgrade from there...
  22. Kevo1288

    Oil Catch Can Drain Point

    Ordered it this morning from amazon. ALL50775 is the part number, its a weldable steel -16an bung.
  23. Kevo1288

    Swapping Banks Sidewinder to an Interim IDI

    :frustrate
  24. Kevo1288

    Oil Catch Can Drain Point

    Well I found that mishimoto makes a high flow catch can for certain applications that has 2 1" ports (1 in 1 out obviously), which is perfect. Meaning I only need to run one can. The whole AN chart and size confuses the hell out of me. For this a -16 weld in bung should be good for 1" id hose so...
  25. Kevo1288

    Can we talk suspension parts?

    On the last comment, they are dangerous parts!!!!!!! I highly recommend against them everytime I can, even though they are the house brand. I have used MEVOTECH on my smaller pick ups I had (sonomas, s10s) and they worked fine. This is my first solid axle truck I have had/wanted to do front end...

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,117
Members
26,431
Latest member
Dusty27

Staff online

Members online

Total: 1,065 (members: 14, guests: 1,051)

Share this page

Top