Recent content by squeekyM

  1. S

    Buyer Advice

    Thanks for the feedback. It is a 4wd truck. I'll be sure to ask about the SCAs, if they have not been used I'll probably walk away unless the price drops significantly. I'll keep you posted on the outcome.
  2. S

    Buyer Advice

    Thanks for the input guys. I know the fuel system (pump & injectors) have never been touched. It is an automatic E4OD, the trans was replaced with a new unit just about 5K miles ago. The owner is asking $6K. That seems a little steep. What do you think would be a fair price, interior is...
  3. S

    Buyer Advice

    Folks, It's been a while since I last posted on the boards. I'm going to look at a '94 F350 CC w/ 7.3L factory turbo later this week. I'm hoping someone can give me a few pointer on what to look for outside the basics. At one point, I recall there being a good link to pre-purchase...
  4. S

    Dana 60 Front End Conversion

    Hi Everyone, Its been a long time since I last posted, getting adjusted to a new job and moving...... anyways, I was looking to buy a Dana 60 (balljoint) front end out of a 2002 f250. I have heard for the most part that these should be pretty easy to bolt up. Is there anything I should look...
  5. S

    clutch kit time!

    First off, thank you Towcat for the help the other day. Based upon his recommmendation, my pressure plate seems to be toasted. While things are apart, I might as well do the entire clutch kit, forks, throw-out bearing, etc. At the sametime I will be replacing the rear main seal. I am...
  6. S

    Firewall Flex Fixing- Help

    Thanks for all the good info. Towcat, I will be giving you a call Saturday...Hopefully you can help me shed some light on my problem. Thanks again.
  7. S

    Firewall Flex Fixing- Help

    I have been thinking the same thing about the High Pedal Effort. Where should I start. I know the clutch slave and master have been replaced. That leaves me with the throwout bearing and clutch forks???? Is that right. Can I replace the clutch fork with the trans still installed, or is that...
  8. S

    Firewall Flex Fixing- Help

    Thanks for the info. After taking a look a the TSB I do not think it will be that bad. I will be going with the large kit.
  9. S

    Firewall Flex Fixing- Help

    I just crawled under the dash to inspect the area. I cannot find a crack anywhere. I remember reading somewhere that a little movement of the clutch master is normal??? Either way it is moving....should I simply for now install with the small reinforcement kit for now and see if there is any...
  10. S

    Firewall Flex Fixing- Help

    Hi, Over the past few months, the clutch on my truck has become more and more stubborn. Today I had someone push in the clutch pedal while I checked the firewall. Sure enough, the clutch master moved a decent amount. Time for the LARGE firewall reinforcement kit. I have read a few old...
  11. S

    Tire Pressure

    I think the weight that I guessed was way off then. For some reason I thought I read somewhere that these trucks weighed almost 9000#. Aside from a few motorcycles from time to time, this truck is empty/unloaded. Sounds like it is closer to the 7000# mark. What would the inflation/PSI...
  12. S

    Tire Pressure

    Thanks for the info, that was exactly what I was looking for. I just changed the diff fluids, and drained and filled the trans with RedLine MT-90 in preperation for this little "trip". One more thing.... how often are you supposed to change the ATF in the transfer case? Thanks again.
  13. S

    Tire Pressure

    I was curious what PSI some people would recommend running for highway driving. I am going to be driving about 4 hours roundtrip and just wanna check a few things before I head out, one of them the tire pressure. I believe the tires are currently @ 60PSI... I wanted to make sure that they were...
  14. S

    Burning electrical

    Thanks for the responses. Is this airbox accessable from inside the cab....similar to replacing the heater core, removing the glove box etc....or is this the thing up against the firewall in the motor compartment?? Thanks again.
  15. S

    Burning electrical

    Tonight on my way home my cab filled with smoke VERY quickly as soon as I turned the heater on. Anyone ever had this happen to them? I started the truck, let it warm up for about 2 minutes then took off. As soon as I started it I set the HEAT to HOT, but left the vents selector at OFF...
See more

Latest posts

Forum statistics

Threads
91,333
Posts
1,130,534
Members
24,136
Latest member
m2rtin

Members online

Total: 861 (members: 14, guests: 847)

Share this page

Top