Recent content by nhwrench01

  1. nhwrench01

    cdr delete question....

    Thanks Nero,, didnt think of that,,, guess im doing that soon..
  2. nhwrench01

    cdr delete question....

    I did search this but got no answer.. so.. Back story, 86" 6.9. bought a used turbo system, 093.. have everything but the valve covers... so no cdr on the engine.. the oil fill tube ( bolted to the injection gear cover} is a 1/4 twist on , i know i need a vent for crank case pressure.. I...
  3. nhwrench01

    Looking at picking up a spare IP?

    Dustyman, this is the company i went with for my ip in my 6.9. Wess is very smart with all things IDI.. I checked about all places to get a reman pump from... some were much cheaper,, but , you get what you pay for, and ( being a mechanic for 40+ years, ) " Buy once, Cry once." Do it right, and...
  4. nhwrench01

    DB2 Fuel Intake Thread

    old post but, same here,, going the hardware store tomorrow for that same fitting...
  5. nhwrench01

    6.9 low power/no power.... need help

    p.s. truck is unloaded, 4x4 not engaged, running on clean diesel,
  6. nhwrench01

    6.9 low power/no power.... need help

    well i rechecked timing, was right on at 8*... i did back it off to 7* and went for a test drive to warm it up and see, if the grayish smoke and power was any different...,, about the same.. on the way back ( on a class 6 dirt road, hard packed dirt) i came to a dead stop, on a very slight...
  7. nhwrench01

    Dana 60 Axle shaft Seal Replacement

    when you are there, the axle will be mostly empty, ( pinion gear will be there ) but the ring gear and both axles will be out ( have to do this to replace axle seals) i run a rag and shop air to clean out dirt from the axle tubes, this might take some time to get them clean if you hit the mud...
  8. nhwrench01

    6.9 low power/no power.... need help

    i will recheck timing this weekend,,, ... what is the HPCA switch,, thinking the timing advance in the ip?.. ... i will report back after things are checked, working a 1/2 weekend .... But thank you for the help.. .
  9. nhwrench01

    6.9 low power/no power.... need help

    I have a gunson for the diesel and a timing light with a advance feature.
  10. nhwrench01

    6.9 low power/no power.... need help

    Kdo58… the lift pump is new. I know that doesn’t mean good, but with the old pump I had 2.2- 3.6 psi at idle. Now I have 4.5–5.5 psi… and it doesn’t die when the psi goes to 0, but this is at 2200-2300 rpm. 3/4 throttle and up hill… psi returns fast when I let off
  11. nhwrench01

    6.9 low power/no power.... need help

    The timing was off 7* retarted.. it did get very hot ( coolant) going up hills . And is now better. But very low power.
  12. nhwrench01

    6.9 low power/no power.... need help

    History on this truck, 1986 f350, (f250) badges. bought for a D.D. as my 93 350 7.3 has been retired.. so, the new truck , i have some paperwork with it, bought new by the ING corp, in Colardo, then in 2021 was in maine and registered with 245k on it.. i have done,,, used c6 trans (works good)...
  13. nhwrench01

    Blower motor

    If your talking about the blower motor( as the heading states ) id look at the resister and the plug to it,, with hi amps and time, the plug might be getting hot , slowing the voltage ...?? try unplugging the resistor plug,,, should be easy to pull off ( relatively)... look for the plug to...
  14. nhwrench01

    Air filter

    for me,,, id leave the stock filter and box on, that filter ( even with the air duct on) will suck in more hot air from under the hood than anything. the only aftermarket " cold air intake " types ive seen had a box around the filter with a tube or snorkel into the fender or behind the grill...
  15. nhwrench01

    oil filters on ebay,,,get them cheap

    wow, didnt know that,,, well i tried ...
See more

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,941
Members
26,573
Latest member
Oiler

Members online

Total: 1,655 (members: 8, guests: 1,647)

Share this page

Top