Recent content by mustangmatt89

  1. M

    4x4 Conversion

    I’ve been looking for a new f250 and I found one that is a really good deal. But it is a 2 wd.. I have a boat I haul and really should have 4 wheels drive. It’s about 10k and a steep ramp that is heavy traffic and always wet. So I wouldn’t have to do it immediately but how awful would a 4 wheels...
  2. M

    FMV of f250 or f350 idi

    I’m pretty sure I’ll be getting one in a different part of the country. In md where I am at trucks that are 10 years old have rust issues... Debating whether I need a 4x4... I’m never going to drive it in the snow but I have a 30 ft scarab that will be launched and pulled occasionally.. I’ve...
  3. M

    FMV of f250 or f350 idi

    That looks like a good find!
  4. M

    FMV of f250 or f350 idi

    I’m thinking my budget will be $10k... but looking at prices it may be $15k that is needed for a solid truck that has a some what presentable paint job still on it and mechanically sound.
  5. M

    FMV of f250 or f350 idi

    I sold my 93 f250 idi with a banks turbo maybe 2 years ago because it was just sitting with a locked up rotor and the frame was starting to rust and if it wasn’t addressed soon it would be a frame replacement and at the time I had zero time to do it... I’m looking to get another truck and...
  6. M

    F series 460 engines feedback

    I recently sold my 93 f250 7.3 idi. I had it for 15 years did a mild restoration maybe 10 years ago, new bed sides, fenders, paint etc.. looked nice on the outside but the frame was just about done from rust so I sold it since I also had almost 400k on it. So I am in the market for another...
  7. M

    Fuel oil in 7.3 idi

    I just got rid of my boiler in my house and have probably 40 gallons of heating oil left in the tank... Any issue with just putting this in my truck to get rid of it? 1993 Ford F-250 7.3 idi with a banks turbo kit
  8. M

    93 ford f250 7.3 4x4 transfer case linkage

    http://www.summitracing.com/parts/rnb-600-602/applications/model/f-250/engine-size/7-3l-445/year/1993/submodel/xlt anyone know if this would actually work for or has anyone tried the dorman one?
  9. M

    93 ford f250 7.3 4x4 transfer case linkage

    So after replacing all of my front ball joints, bearings, seals, and universal joints. Today the linkage that shifts it into 4x4 broke. I looked underneath and it was split in two where it mounts. Does anyone know where I can find one online or do I have to go to ford? My truck is a 93 ford f250...
  10. M

    Rebuilding front end 93 f250 dana 50

    One last question.. I would like to replace the bearing that is inside of the spindle as well along with any seals that are in the area. In the picture it looks like parts 58, 59, and 50 I would need, does anyone know what they are called and where I can find them... And are dust shields...
  11. M

    Rebuilding front end 93 f250 dana 50

    Thanks for the replies... That is what I figured I was going to have to do was pull the center section. I was thinking of maybe adding 2 studs to make installation easier. And that U joint is bad.. all of my u joints were horrible but I do have almost 300k on the truck now. The slip joint was...
  12. M

    Rebuilding front end 93 f250 dana 50

    I have a 93 f250 with a dana 50 in the front. I am replacing the ball joints and have them pressed into place and I have one problem. The passenger side axle was 2 pieces and I removed it at the slip joint under the boot. How do I remove the other section so I can replace the u joint? Is there a...
  13. M

    Buying the correct vacuum pump 7.3 idi

    Thanks, I saw this one listed at my local autoparts store and found it on summit racing for a lot cheaper. Thanks! I knew I had to change out the pulley but I did not know I had to fill it with oil. If anyone can chime in on that area it would be much appreciated.
  14. M

    Buying the correct vacuum pump 7.3 idi

    Hi everyone, Since the autoparts store had many to choose from and non in stock I wanted to make sure I was buying the correct pump Has anyone tried the dorman Part Number: 904-807 and does it fit. I have a 93 ford f250 with a 7.3 idi originally a non turbo but I have the banks system...
  15. M

    Really hard break pedal 93 f250 7.3 idi

    Thanks for the reply, I am pretty sure it is the pump but wanted to see what others thought about it. When I pull one of the hoses off I can usually here it drop in pressure. Also my gauge only ready 5 ibs and I thought that was really low while it was running.
See more

Latest posts

Forum statistics

Threads
91,292
Posts
1,129,831
Members
24,106
Latest member
lewisstevey7

Members online

Total: 678 (members: 5, guests: 673)

Share this page

Top