Recent content by haubert
-
zf5 swap no start
Thanks cpdenton that will save me a lot of time I have all data but it's hard to find the correct diagrams- haubert
- Post #10
- Forum: 6.9L IH & 7.3L IDI Diesels
-
zf5 swap no start
93 f350 7.3 I installed a fresh rebuilt 7.3 while I was at it I swapped out the e4od tranny with a zf5, I installed a factory manual steering column, I don't have no neutral safety switch hooked up and I removed the e4od wiring harness from the truck, everything seems to work when I turn the key...- haubert
- Thread
- Replies: 16
- Forum: 6.9L IH & 7.3L IDI Diesels
-
zf5 swap
Ok thanks Sent from my SCH-I545 using Tapatalk- haubert
- Post #8
- Forum: 6.9L IH & 7.3L IDI Diesels
-
zf5 swap
I have a 93 7.3idi swapped out the e40d with a zf5 also installed the single mass flywheel clutch conversion kit. getting ready to instal the clutch brake assy. my question is im not sure if theres a particular slave cyl that I need for the single mass. I have a master cyl slave assy from a 91...- haubert
- Thread
- Replies: 18
- Forum: 6.9L IH & 7.3L IDI Diesels
-
-
E4od to 5 spd swap
Ok thanks, I appreciate All the forums advice. Can't afford to learn by, my own mistakes LOL- haubert
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E4od to 5 spd swap
Anyone know if the 5th gear is 1:1 also thanks now will the newer 6 spd bolt right up. Just trying to figure out if I'm going to need a gear vendor unit for the highway running when I switch over to manual thanks- haubert
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E4od to 5 spd swap
Forgot to add my truck is a 93 f350 7.3- haubert
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E4od to 5 spd swap
I was at the scrap yard today looking for a 5 spd tranny looking to convert from my e4od. All I could find were older 4 spd what do you think of the 4 spd or should I hold out. I use the truck for heavy pulling are the final gears the same ratio- haubert
- Thread
- Replies: 6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
What temp sensor
Ok thanks for the schooling my truck is a 93 just assumed being to sensors one was for computer like a gasser thanks Sent from my SCH-I545 using Tapatalk- haubert
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
What temp sensor
Ok thanks that's the sensor I removed to install guage it's a single wire. Just wanted to make sure it wasn't the temp sensor for computer Sent from my SCH-I545 using Tapatalk- haubert
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
What temp sensor
What i was trying to say i installing a coolant temp guage what's the location for guage sending unit and computer sending unit Sent from my SCH-I545 using Tapatalk- haubert
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
What temp sensor
I installed a coolant temp sensor. I thought the sensor on the driver side front head is for guage. Installed probe hooked up guage and my in dash guage still works. Did I remove the wrong sensor or will the computer sensor reads to guage also Sent from my SCH-I545 using Tapatalk- haubert
- Thread
- Replies: 6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Exhaust
That's a good deal. Let us know how it fits. Sent from my SCH-I545 using Tapatalk- haubert
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
QUICK QUESTION ABOUT INJECTOR CODES.
I'm running the United technologies code b in my 93 7.3 runs fine for $40 buy them you could always have them pop tested before installing if your unsure Sent from my SCH-I545 using Tapatalk- haubert
- Post #6
- Forum: 6.9L IH & 7.3L IDI Diesels
