Search results

  1. J

    smoking knocking

    hey guys and gals ive got a buddy with a problem he has a 05 sd with 115k on clock all stock it has just started knocking in the top of engine on the pass side and white smoking bad. i can say he more than likely has egr problems but what would cause the knock it only does it when up to...
  2. J

    cranky cranky no start

    got a buddy with a 97 f250 4x4 250k on clock service reg at 6k all of trucks life. no problems until today truck ran just fine shut it off and no start i checked it out and cranks good tach comes up to 500rpm when cranking but no start no smoke out of tail pipe either. tach does not bounce when...
  3. J

    1985 f250 4x4

    1985 f250 sold sorry guys sold truck to a local buddy got $500.00 for it so i guess both of us were happy he needed a truck and momma said i didnt need 2 oil burners so i made her happy to, that makes me happy.
  4. J

    1985 f250 4x4

    sorry no pics truck may be gone today if not i will try to get some pics.
  5. J

    1985 f250 4x4

    i have for sale a 1985 f250 ext cab 4x4 with 6.9l auto c6 old truck need glow plugs toggle switch got left on. the truck is kinda rough it needs heater core and a good cleaning it also has som rust on the bed and on the cab it is brown and tan in color, it has pdl an pw sometimes work. it runs...
  6. J

    clutch

    ok so you guys were right about power adders and a stock clutch didnt have my chip in for a week and smoke my clutch i havent tore it down yet but i have done a bit of price checking. i have a question will my truck have a solid flywheel or a dual mass one i am getting conflicting reports from...
  7. J

    guages

    where did you find a R size drill bit no one seems to know what im asking for at the parts store.
  8. J

    I am installing a Horton Fan Clutch on my OBS. Here we go…

    watch out be carefull horton is expensive and no tech support i work at a school and ive had to replace a few due to wires being broken at the clutch with no way to rebuild or repair last one i bought was $725.00 for a cat c7.
  9. J

    wheels

    i was wondering where i could get some factory match wheel paint, my wheel are starting to rust. ie{stupid dogs}
  10. J

    guages

    just ordered a set of glo shift guages and to get the best deal i had to go with a 3 guage set i got boost egt and oil temp i dont have a auto tranny so no need for trans temp i was wondering where to tap in to get engine oil temp. and is there a fitting i can take out to get boost pres instead...
  11. J

    dual wheel

    i pull a 25ft gooseneck flatbed and it has tandem duals i i like the look first off and with duals i could use the truck spare for a trailer spare. and i like the stability the duals offer and i am planning to put a flat bed on this truck.
  12. J

    dual wheel

    i am wanting to convert my single wheel truck to duals how is the best way to do it are the axels the same in the back or are the dual wheel trucks wider and are the spring peches the same on both if they are wider also on the front is it the same with a different hub or a totally different...
  13. J

    does anyone know where I can get a cheap exhaust stack kit

    stack kit i made my own kit i bought all of the reducers and elbows from napa and i got a 6 inch miter cut free from the local truck shop it was one the had cut off of a wrecked truck. i think i may have $120 bucks in the hole thing. as far as cutting the hole in your bed hole saws are...
  14. J

    hard to start

    i know it has a glow plug relay this truck seems to have 2 is that right or am i looking at the right thing they both look like starter relays to me they are both behinde the fuel filter.
  15. J

    hard to start

    my truck has just started to get hard to start it is 40deg+ in the mornings i can cycle the key of and on 4 or 5 times each time letting the wait to start light to go off and then it will start and white smokes allot whith a hint of blue and runs kinda rough then iclars up after a second and...
  16. J

    blowing ignition fuse

    im working on a 2000 3500 5.9 6spd the truck will blow the 20amp ignition fuse in the dash it wont do it all of the time but it is getting worse i have checked all of the wirring to the starter no problems im thinking it may be the starter but not sure anyone had this problem?
  17. J

    straight pipe

    well i took the muf and cat off my truck saturday did not see much improvement on hp or torq but i havent hooked it to anything yet, did notice a big improvement in sound you can actually hear the turbo now i was wondering if the psd have a silencer ring on the turbo like the cummins do. also if...
  18. J

    4x4 and rear axle question

    no i did not i was to worried about grabbing gears to get enough wheel speed to clean the tires out we were sinking fast. southeast missouri mud is unforgiving. i havent changed the fluid yet either the truck has about 90k on it i just bought it couple of months ago
  19. J

    4x4 and rear axle question

    i hav a question about my truck it is a 2001 f250 7.3l 6spd 4x4 my question is if there is any way to check if i have a locking diff without taking the cover off, the build sheet says that it is but yesterday just about stuck it and only on wheel was pulling. also on the 4x4 what direction do...
  20. J

    coolant leak

    is this something that i should be woried about? it is not leaking very much but im not one to let things like this go i guess what im asking is if this can lead to other problems down the road.
  21. J

    coolant leak

    it is where the pipe bolts onto the water pump
  22. J

    coolant leak

    where the lower hose connects to the water pump
  23. J

    coolant leak

    i have a 2001 f250 sd 7.3l man 6spd 4x4. It seems to be leaking from the lower radiator hose elbow that comes off of the engine it looks to be coming from the flange that bolts the two elbows together . my question is if there is a gasket on this flange or if the bolts could just need...
  24. J

    napa exhaust mods

    i was just on napa website and found some exhaust pipes for 7.3l i was wondering if these will work on my truck i am wanting to delete the cat and muf without spending much cash. my truck 2001 f250 xl 7.3l 4x4 6spd excab longbed.
  25. J

    edge controler

    i am interested in the diy air intake do you have any pics. also i have seen pics of the factory ford aic controler do you have any info on this.

Latest posts

Forum statistics

Threads
91,306
Posts
1,130,027
Members
24,117
Latest member
olsen726

Members online

Total: 718 (members: 9, guests: 709)

Share this page

Top