Search results

  1. J

    1995 flywheel question

    I'm swapping a 1995 powerstroke into my 1994 turbo diesel idi truck. I haven't pulled the idi yet and when I built it years ago I used a luk single mass flywheel. My question is can I use that flywheel with an upgraded clutch on my powerstroke?
  2. J

    Power windows

    My fuse box is toast. The thing is I think I can just wire them up stand alone and keep my new harness and box.
  3. J

    Help identifying plug on under dash wiring harness?

    It's in the green look for the srs system. It's for air bags and the magical light is on so that explains this plug. Every thing else works perfect except the windows locks and air bag light is on.
  4. J

    Power windows

    It's obvious at this point that it didn't. My fuse box had additions for 3 extra plugs where this one only has one. So from here how can I tie in and wire up my windows? Set up its own fuze box and relay? Not 100% sure how to go about this?
  5. J

    Power windows

    My truck is a 1999 ford xlt. Not sure what year the doner truck harness is. I just replaced the under dash harness and fuse box. All my power window wiring in the cab is still there. I didn't see any plugs left undone.
  6. J

    Power windows

    I just replaced the underdash wiring harness with a used one as well as my underdash power distribution box. Everything works great except I have now power windows or power locks. I'm guessing whatever truck my used replacement harness came from didn't have power windows and locks. Does anyone...
  7. J

    Help identifying plug on under dash wiring harness?

    There was not a box plugged into that connector, it has a harness that runs several different areas. It's loomed with the green loom which is normally for air bags. I don't think its the AIC.
  8. J

    Help identifying plug on under dash wiring harness?

    So I traced the wiring in the underdash harness and it goes to 5 different locations/plugs. If I don't adapt it into my new harness will it effect the truck in anyway?
  9. J

    Help identifying plug on under dash wiring harness?

    What is an AIC plugs function? Is it nessicary?
  10. J

    Help identifying plug on under dash wiring harness?

    No I actually have the trailer wiring hooked up just like my original harness. This looks like something safety related maybe.
  11. J

    Help identifying plug on under dash wiring harness?

    So long story short my windshield leaked on my 2000 psd 2x4 xlt Crew cab long bed auto truck. The underdash harness and fuse power distribution box corroded and malfunctioned. My dad gave me the truck. I pulled the dash and purchased a used harness and box on ebay. Everything looks good and...
  12. J

    Turbo upgrade?

    I have never hurt pistons and rings due to high egt's but I have wollard out valve guides and burnt exhuast valves.
  13. J

    Turbo upgrade?

    I can't recall what the timing was at. I just had it set at an injection shop and it runs better. I played with the timing allot without the timing meter and my egt's ranged from 700-850 and that was about all it would change. At 70 it's at 7psi with a psd intercooler. It getting good mileage...
  14. J

    Turbo upgrade?

    Wow I'm at 800! I must have to small of a turbine.
  15. J

    Turbo upgrade?

    What are normal unloaded cruising egt's at 70mph?
  16. J

    Turbo upgrade?

    The truck has a body lift and I have enough mandrel bends to completely fab a new hot side and down pipe.
  17. J

    Turbo upgrade?

    Thanks I will check it out. I'm not looking to race. I'm looking for pulling power with low egt's.
  18. J

    Turbo upgrade?

    I'm not sure how much fuel my pump is good for. I noticed the s300 has a few different turbine sizes any clue on which one would work best? What A/R?
  19. J

    Turbo upgrade?

    I have no problem using an HX35 how much power can they support? Is there a way for me to delete the pedestal? What about the hole on the back of the intake? I think I want to make a custom turbo merge as I already have a few minor exhaust leaks on the factory ATS up pipe.
  20. J

    Turbo upgrade?

    I am running a 3" out of the ats housing then to 4" at the bell housing all the way to the back of the truck with no muffler. The turbo sounds like its struggling to keep up and I think the turbine is just to small now. I just had the timing set and I am not even rolling any coal. Just a very...
  21. J

    Turbo upgrade?

    Well I think I have hit a wall with my truck and my turbo may be holding me back. I am running an ats turbo with an upgraded exhaust and compressor wheel. I have the upgrade ats turbo outlet housing and a a machined compressor housing with larger compressor wheel. The issue is I make about 14psi...
  22. J

    Waste gate tie back?

    Truck hit 14psi today. Runs hard. I just needed a better road to open her up on. 4th gear is a 14psi ripper for sure. Now I have another issue. For some reason the glow plug controller will start clicking loudly when the truck sits at idle for a while. The temp gauge is on the cold side. Is the...
  23. J

    Waste gate tie back?

    Thanks, I didn't want to get a thread flared up. I don't believe adding IP timing will increase my boost but it should allow me to run more than I have at a lower temp. No doubt it was retarded as I made a small adjustment to it and the truck came alive. I still think it needs just a bit more...
  24. J

    Waste gate tie back?

    Not trying to hurt any feelings or pot stir but there is nothing wrong with my DPS pump. Matter of fact it has totally changed the way the truck drives. I think it has allot more in it. The DPS head studs I had went to Shizil on me but this pump is amazing. Just calling a spade a spade. I'm...
  25. J

    Waste gate tie back?

    Type4 I think you were the one I sent my turbo to years back. Machined the compressor and put a bigger wheel I think. Was that you? The truck runs strong but has allot more in it. I already outran my dads 1999 factory 7.3l ps. I just know it has more at only 11psi. What would normal unloaded...

Latest posts

Forum statistics

Threads
91,284
Posts
1,129,794
Members
24,099
Latest member
IDIBronco86

Members online

Total: 803 (members: 8, guests: 795)

Share this page

Top