Search results

  1. 6.9poweredscout

    Engine wiring diagram?

    I bought a manual on a disc, searched it and googled for about an hour now. I cannot find the wiring diagram for my 91. I'm looking for the diagram that shows the engine sensors (temp, oil, high idle, and fuel solenoid), headlight diagram (trying to figure out that silly DRL plug and how I can...
  2. 6.9poweredscout

    Fuel and brake line clips?

    Does anyone have a part number for ford or aftermarket to get the little 3 clip tabs that go on the frames that hold the fuel feed and return and brake lines on our trucks? Tried searching for something similar, but all I find are those silly billet ones that are $25 each!
  3. 6.9poweredscout

    Hydroboost weephole leaking???

    If you're looking at he hydroboost from the front of the truck there's a little hole on the side of the hb cast body by the blue cylinder. Mine started leaking 2 months ago. After a whole bottle of Lucas stop leak didn't help i bought the reseal kit. Now it's not steady, on and off at random...
  4. 6.9poweredscout

    Bad headgasket? The big C? Might be DT time....

    1991 7.3 banks sidewinder, 90cc pump, 80k on engine. Has hit 18 psi boost, egts upwards of around 1250 never longer than a few seconds. Was going to Lancaster to deliver a truck, was about 2 hours in, passed all the hills where the egts and boost was high so I wasn't watching the gauges as much...
  5. 6.9poweredscout

    CCLB 2x4 DRW- 4x4 SRW With PMF RSK

    Finally did it! When I got the RSK kit. On pre '92 trucks it took some cutting so the best route was to burn it on! 99+ x code springs Bilsteins Parts rig for the shackle brackets and various other pieces use 3 to make 1 good one! Cleaned and...
  6. 6.9poweredscout

    RSK trac bar location....

    Since I'm converting to 4x4 i need to drill the frame crossmember for the trac bar mount. Now i know it's recommended to go with the adjustable trac bar, but couldn't i just bolt the axle in, bolt the arm to the bracket, then mark the holes where it sits and drill the holes? Or is there geometry...
  7. 6.9poweredscout

    1991 F350 4x4 +2.5 RSK Bilstein 5100 shocks?

    I have everything but the shocks to complete my 2-4x4 conversion with my 2.5" RSK. Been searching for Bilstein 5100's with no luck. will "stock height" shocks work? And has anyone purchased the 5100's for a 4x4 F350? do you have the part numbers, I can't seem to find anything. thanks! ;Sweet
  8. 6.9poweredscout

    DT360 into 1991 F350

    Just a teaser. My IDI runs so well I don't have the heart to pull it yet. Just acquired 2 DTA360 engines, a 1991 185HP and 1992 190HP. The plan is to get the adaptor plate to bolt it to my ZF5 and just tweak the pump a little. Picking them up: Also grabbed a 1956 IH S-120, towed the...
  9. 6.9poweredscout

    F super duty 2wd Pitman arm the same as 4x4 F350 arm?

    There's 2 super duty trucks in the yard near me, haven't found any 4x4 350s. I thought i read the arm from a Fsd would work. Anyone know for sure?
  10. 6.9poweredscout

    Bricknose speedometer cable won't stay in place.

    My speedometer worked fine for months after swapping the zf and tcase until last week it stopped. I pulled the cable/cruise speed sensor piece out and it just broke in half. Got one from a junk yard, worked for a few days, same issue, bought a new one and it worked for a little while then...
  11. 6.9poweredscout

    Blend door operation

    I'm assuming the blend door is connected to that vacuum actuator on the heat/AC box under the hood correct? Now I've never had a issue with heat or AC and the fan blows good on all settings. I did the heater hose vacuum actuator valve to help get cooler AC. Hooked it all up and switched it to...
  12. 6.9poweredscout

    Friends burning up passenger side window motors.

    I've been going through passenger side motors. I notice my friends that ride shotgun always bump up or down the windows with their knee. I noticed the other day after I dropped off my friend the window wouldn't go up. Then I realized it, he probably had his knee on it for over an hour and...
  13. 6.9poweredscout

    diverter valve on heater hoses.

    Installed the ranger valve on my heater core hoses, ran the vacuum line to the one on the box. Now with the fan ac/heat off there's vacuum on it. When I switch it, it doesn't change. I remember on my Stroker when I did it and put the AC on max it'd switch the valves. Am I missing something?
  14. 6.9poweredscout

    Looking cavitation in the eye.

    Most of us know what cavitation is, but never saw what it looks like from the outside of the cylinder wall. Here's a section from a V12 Cummins that filled a cylinder with coolant under load and grenaded the liner, piston and rod.
  15. 6.9poweredscout

    what shares tach and voltage gauge wires?

    Noticed last night in my '91 that the tachometer and voltage gauge are not working. Just wondering if there's a common wire I can start at to figure out what's wrong.
  16. 6.9poweredscout

    some trucks bleed air better than others?

    I've noticed if I run my truck low on fuel and it picks up air (gauge is off...I cut it too close sometimes) its a pain to restart even with an electric pump. Yet I've run other trucks I've owned out and just a few seconds cranking lights right off. I it cranks fast, and I'll bleed injectors and...
  17. 6.9poweredscout

    Doing rust belt things to a "clean" rust belt truck.

    To all you left coasters.... :mad: enjoy your clean sheetmetal. I could no longer take my fender laying on and smashing my bumper when skipping pot holes.... had to do some rust repair. sorry, phone picked up some glare. the pass side...
  18. 6.9poweredscout

    Bricknose bumper and headache rack action!

    Was sick of the bent aftermarket rear bumper, got some materials for a bumper and headache rack! Mack u bolt gotta weld 2 tie down points on the rack then some paint action. Inbetween building it i installed new door lock cylinders, man...
  19. 6.9poweredscout

    reverse shackle front, what to do in the rear?

    This summer I plan on a reverse shackle/Dana 60 swap on my 2wd dually. Now that'll probably get me like 5"of lift up front right? So what's everyone do in the rear? It's a tow rig so 6" blocks in the rear is kind of scary. Can I use lift springs out back?
  20. 6.9poweredscout

    Beating a dead horse. Traction bar idea.

    Ok I love simple. I have had great luck with the simple 1 bar on each side design, from bottom of axle, couple foot of round bar, tied to frame, bushings on the ends. Seen this numerous times on tow rigs and competitive pullers. On the travelette I've lost sleep over several designs, but I think...
  21. 6.9poweredscout

    Brick nose cowl hood?

    Anyone have a cowl hood on their brick? i'm thinking of putting one on/making one when I repaint my truck.
  22. 6.9poweredscout

    Installed the PSD bumper opening to my '91.

    Just thought i'd share. My friend got a plasma cutter so it literally took 5 minutes! ;Sweet
  23. 6.9poweredscout

    7.3 Vs. 6.6 Durajunk

    My friend decided he'd prove to his friend why a $600 truck is better than a $20,000 truck. Yes that old ford the first idi I owned still working hard. This wasn't a one time fluke, this was 3 of 3 and the ford got all 3 pulls. That 6.6 is worked up too! LOL:rotflmao;Sweet:D...
  24. 6.9poweredscout

    Clearance lights for 1991 350

    I had bought the oem replacement ones for my 97 and recall them being being around 45 bucks for all of them, I've been searching lately and they're about $15 each. Anyone have any good places to get them from?
  25. 6.9poweredscout

    asked about just gas tanks, what about larger fuel tanks??

    is there any larger fuel tanks available for a '91 that doesn't cost $500 each? seeing as I have to do both i'd rather go with larger ones..

Latest posts

Forum statistics

Threads
91,299
Posts
1,129,916
Members
24,108
Latest member
Lance

Members online

Total: 546 (members: 14, guests: 532)

Share this page

Top