Search results

  1. FoMoCo

    Still no Boost

    I just replaced the injectors with Stanadyne G codes that were pop tested, rebuilt IP, new o-rings, caps and return line. Clean Air filter, fuel filter has less than 1,000 miles on it. The truck has been timed and is at 10 degrees. I can only get maybe 3 lbs of boost if I nail it in top gear...
  2. FoMoCo

    Fan clutch removal help?

    I got the tools to remove the fan clutch from the auto parts store, but I just can't seem to get the old fan clutch off. It is hard to hold the keeper and pry on the wrench. My question is: are these fan clutch right to tight or left to tight. In other words do I press the wrench towards the...
  3. FoMoCo

    New A/C problem

    I had a clogged condenser and I installed a new one along with a new drier and O-tube. I removed and drained the compressor overnight and I ran thinner through the evaporator since this would be the only thing to hold oil, I also ran thinner through the lines. I wanted to get the correct amount...
  4. FoMoCo

    A/C gods needed

    I am having A/C problems, not cooling very cold and building high pressures. I have changed out the evaporator, orifice, and drier. I had a leak on the high pressure port and I broke the high pressure sensor, So the system had no freon, I fixed the above items and I pull vacuum on the system...
  5. FoMoCo

    Just installed new injectors and IP, only idle now

    I just got done installing a rebuilt IP and new injectors with a line kit. The truck will fire up no problem and no smoke, but it will only dle with reduced power. Did I get the IP off 180 degrees. I have a intercooler and I might have forgot a blue towel and that could be clogging the air...
  6. FoMoCo

    Where to buy Stanadyne DB2 parts?

    I was installing my rebuilt injection pump and I broke the arm on the drivers side of the IP. It works off the throttle and controls the thing on the bottom of the IP. It has a pin in the middle, a roller on top and the lower is just a set screw. Works like a see saw. Does anybody know what it...
  7. FoMoCo

    Pop Testing New ones and IP ?

    I have a few fuel leaks at the injectors, so it is time for the new injectors. My question is do you need to pop test the New stanadyne injectors? I can have them tested, but I would have to wait until next week to reinstall them. Second question, The truck runs fine, but since I was...
  8. FoMoCo

    3rd Clutch Master leaking

    I have installed 3 clutch masters on my 1994, The first 2 were from Napa and they looked just like the one that was on the truck when I bought it about 10 years ago (the black plastic ones). The first Napa one I bought as a kit which included the Master, new Line and Slave cylinder, so the line...
  9. FoMoCo

    I need a new IP, how to contact Moose

    Truck has been slow to start lately. The IP went out????, I have fuel going to the IP and the FSS has 12 volts. I remove a line going to a injector and no fuel at all. How do I call and get a Moose pump, I have new injectors and a line kit. Just need a phone number to the Moose. My truck has the...
  10. FoMoCo

    2 Trucks for sale, both 1994 idi 4x4's

    I have TWO 1994 factory turbo trucks for sale. The lifted truck has some upgrades, ATS air to air cooler, gauges, redhead steering box, custom rear bumper and side steps that can be used as air tanks. The lifted truck is my weekend driver and the body is in great shape (no rust), could use new...
  11. FoMoCo

    Help on 1980 International Harvestor 684 with 3.9 diesel

    Hello everybody. I just bought a IH Farm Tractor model 684 knowing it had problems. The dealer that I bought it from said that the problem might be low compression. They had the Injection pump and injectors rebuilt, and the engine is hard to start when cold. You have to crank it and then it...
  12. FoMoCo

    Still delay in starting

    OK, just changed the lift pump and the truck still has a delay just like before in starting. It turns over very fast, but the delay in starting is not consistent. I know the old lift was bad since it leaked when could out of the whep holes. What could it be???? Maybe time for Injection pump and...
  13. FoMoCo

    Rotella T6for sale and Bardahl Flushing Oil

    FYI Autozone has Rotella T6 the full synthetic on sale for 19.99. After I changed my Lift pump, I was worried about getting stuff in the crankcase so I used the Bardahl Flushing Oil and after running the truck for 15 to 20 minutes, I changed the oil and I have driven the truck a few miles and...
  14. FoMoCo

    Changing Lift pump FYI

    I just changed the lift pump on my 94 idi and it was a challenge. No special tools needed, but you will need a Torch to heat up the metal line going to the lift pump from the filter housing, since I had to disconnect the line at the filter housing and pulled the lift pump out with the line...
  15. FoMoCo

    Holley mechanic fuel lift pump? Fan Clutch?

    I say this Holley high performance fuel pump at O'reillys. The pressure is 7 psi, is that enough or to much. Will this pump work on a 1994 factory turbo idi? http://www.oreillyauto.com/site/c/detail/HOL0/12860.oap...
  16. FoMoCo

    Clutch master/slave ?

    I just recently replaced the clutch master with one that is made of aluminum and not plastic, got it form Clarks auto. It works great, the only issue is this master is angled, so it is hard to add fluid and the Max and Min levels don't mean much. The reason I went with this metal one is that I...
  17. FoMoCo

    Fuel lift pump?

    I need a new lift pump, since mine leaks when cold. I was going to go to International and buy one, but noticed that O'reilly's has a Delphi brand pump for 39.00 dollars. Delphi are good, has anybody installed one of these pumps? FYI, ford wants 163.00 for this same pump. This is the diaphragm...
  18. FoMoCo

    International part numbers

    Hello everybody, it has been awhile. I was looking to order a new fuel pump for my 94 idi and I cannot find my International parts number list for these motors. I also don't remember were I got it, been years. Does anybody know were I can find the parts list?
  19. FoMoCo

    Glow plug delete ?

    Need some help from the experts. I live in deep south Texas, and it might get below freezing for a day or so for a few hours every other year, or it will not freeze for 4 of 5 years. So, why do I need glow plugs. I would like to remove and delete the GP's, since they can be a cause of engine...
  20. FoMoCo

    Brake fluid gone

    Went to drive my parts truck around the farm today, and the brakes were not working as usual. The pedal would go to the floor and when I checked the Master it was empty. Got lucky and refilled the Master and the brakes are back but not as firm as they should be. The problem is I can not find the...
  21. FoMoCo

    For Sale 2 - 1994 CC 4X4's

    I have 2 1994 F-350, crew cabs, both are 4X4's and they have the same 7.3idi turbo engines, and both have the ZF-5. The trucks are basically the same, even the same color(teal). The only difference from the factory is 1 truck has the 4.11 gears, and the other one has 3.55?. One truck has been...
  22. FoMoCo

    Clutch Master cyl

    I have a clutch master that is leaking on the inside on the cab, and this master is only a few years old (got it from Napa). Is there a overhaul kit for these masters? and if not can I retro-fit a metal master cylinder to work. The main problem is the brake booster is very close to the clutch...
  23. FoMoCo

    Where to have a 7.3 IDI timed in Texas

    Hello everybody, I am a new member here, I have two 1994 F-350 CC 5 speed 4x4's with the factory turbo. My main truck has the upgraded ATC exhaust housing with a 4 inch exhaust, the ATS air to air cooler, and it also has an open air filter. I of course have EGT and Pyro gauges. The problem...

Latest posts

Forum statistics

Threads
91,348
Posts
1,130,808
Members
24,148
Latest member
Alleycat

Members online

Total: 189 (members: 3, guests: 186)

Share this page

Top