Search results

  1. wftree

    99.5 F450 CC 4x4 6 speed

    I am looking to sell my truck. It has 185,000 miles. New Ford reman engine at 140,000 miles. New clutch last summer. Gooseneck hitch Look at sig for more details $12,900
  2. wftree

    don't buy a Bri Mar Trailer

    We were towing a 6,000lbs excavator on a 12,000 lbs Bri Mar deck over trailer. The tongue snapped off and dropped the deck onto the road. After looking at the design it is very poor. I am stuck with this pieces of crap and will need to weld significant reinforcements to get it back into service...
  3. wftree

    rims for 110 psi rated tires

    I think I need new rims, 16" I am putting on goodyear 235/85R16 14 ply tires 110 psi I think the standard rims are not enough to handle the high pressure. I can not find any rating stamped on the rims. WHere is a good source for rims for my dexter axles?? WFTREE
  4. wftree

    Bob Riley's Fuel system

    Been thinkin of adding a fuel system, I was leaning toward ITP's system but thought about Bob's also. I have bought a lot of stuff from Bob and have always been happy. Can anybody give me the dirt on Bob's system, how easy to install, performance etc. WFTREE
  5. wftree

    what do I risk with new injectors

    A guy is starting to build injectors and I wondered if I should be a guinnea pig. I think the guy is a very straight shooter and I have no doubt his intentions are honorable but I also just replaced my engine :puke: and I do not wnat to do it again. wftree
  6. wftree

    50hp with new engine! split or sigle shot injectors?

    Just dyno'd the new engine with a whopping 50HP increase. :thumbsup: with all the same mods 315rwhp 709ft/lbs torque that works out to $220.00 per HP. :puke: I think the next step is a fuel system then single shot injectors. going to look into Bob Rileys new system. What do you...
  7. wftree

    painting or coating intercooler pipes

    I want to clean up the appearance of my motor. Thought of painting the intercooler tubes high gloss black, to match the re man engine, what kind of paint or coating would work best. Will I have to use High Temp paint??? WFTREE
  8. wftree

    front u-joint/ axle loose

    I was under my truck the other day adding some grease. When I went to grease the front passenger side u-joint it was loose. Not that is was worn out but I could move it up and down. It appears to be moving inside the axle housing? The drivers side is tight Any ideas why. WFTREE I hate...
  9. wftree

    6.0 intercooler for the 7.3

    THIS WAS ORIGINALLY POSTED IN THE "OTHER " FORD WEBSITE. I place it here for your enjoyment With the EXPERT help of the guys from the Western New York Powerstroke Club, Thanks Gar, Jim, Jeff and Kory, I just finished the 6.0 intercooler. The new intercooler is 31% bigger. Original...
  10. wftree

    6.0 intercooler for 7.3

    THIS WAS ORIGINALLY POSTED IN THE "OTHER " FORD WEBSITE. I place it here for your enjoyment With the EXPERT help of the guys from the Western New York Powerstroke Club, Thanks Gar, Jim, Jeff and Kory, I just finished the 6.0 intercooler. The new intercooler is 31% bigger. Original...
  11. wftree

    breaking in new engine?

    I blew up my old engine so I am getting a rebuild. Anything special I should do to break her in. I usually change the oil after only 500 to 1000 miles to clean out any crap. How hard can I run it after I get it home? I will be leaving on vacation as soon as it is done pulling 14,000 lbs...
  12. wftree

    hole in piston! What would you do?

    Finally planned a trip south, 100 miles from home engine starts knocking. Long story involving a single sentance where my wife counted 5 "f" bombs while I talked to AAA. They finally relented and did tow my truck. Short story # 6 has zero compression. Most likely a piece of injector punched a...

Latest posts

Forum statistics

Threads
91,336
Posts
1,130,585
Members
24,140
Latest member
placidoert

Members online

Total: 808 (members: 6, guests: 802)

Share this page

Top