Search results

  1. 88F350idi

    Need to own tools for our trucks

    i have a tool for removal and install of u joints. use it all the time. has paid for itself over and over
  2. 88F350idi

    Sterling 10.25 axle seal question

    thats right.... i have used both in the past. both have worked equally well for me. i agree it seems weird to press in a seal by hand but mine worked fine
  3. 88F350idi

    Oil Pressure Questions

    Thanks. i am quite familiar with the procedure i had it out a week or two ago...
  4. 88F350idi

    Oil Pressure Questions

    Thanks for all the input everyone. i will do a little work on it tomorrow and see what i come up with.
  5. 88F350idi

    Oil Pressure Questions

    could you elaborate on that a little?
  6. 88F350idi

    Oil Pressure Questions

    Hey all, i've got an 88 with a 94 7.3 idi non turbo and i added a factory turbo a while ago. the turbo died about a month ago (which wasn't a big surprise). the shaft bent and was pretty screwed. I had a good spare in working condition that i took in for a rebuild and balancing. while the work...
  7. 88F350idi

    89 CC build thread Frame off resto!! - Bad Idea

    I have a married np205 in my 88 regular cab f350 and it is great...except the front driveshaft does not line up great with the front dana 60 causing uneven compound angles and major vibrations in 4wd. i'm thinking the only real solution is to get a driveshaft with cv's at both ends. just...
  8. 88F350idi

    Turbo Back exhaust for factory turbo trucks?

    I emailed MBRP a few days ago to ask them about turbo idi exhaust and they told me they don't make anything for it, so that must be powerstroke. I picked up a Dynomax / Walker n/a idi tailpipe. it's 4 inch aluminized. modified the hanger so that it sits a little higher and it was pretty much...
  9. 88F350idi

    heat issues

    X2 on the resistor recommendation
  10. 88F350idi

    Hydroboost Question

    Thank you. i do understand all this and it makes good sense to me. With a little more work i should be all set. Thanks for all the input everyone has given.
  11. 88F350idi

    Hydroboost Question

    Thank you for this info. It is what i was looking for. I will go ahead and slot out my master cylinder to fit. Did you have to do the mods to your pedal arm? mine seems to line up just fine (but i will double check)
  12. 88F350idi

    Hydroboost Question

    Thank you. i am running the superduty master cylinder and it seems to be the problem. Which part are you referring to as "intermediate pushrod"? is this the piece that connects to the pedal arm? Thanks again.
  13. 88F350idi

    Hydroboost Question

    Hey everybody, I got my hands on a hydroboost setup from a 1994 F450 superduty and put in in my 1988 F350. I am happy with the added performance of the braking system. However, the master cylinder from the 450 is of a larger bore than my F350. This, i believe, has caused my brake pedal to be...
  14. 88F350idi

    Dumb question of the day(glowplugs)

    Just to throw in my two cents... i think they will get burned anyhow... i have had a set of motorcrafts in my truck for over a year, and they still glow like the day i got em. and my truck sees plenty of cold starts (minus 18 this morning)
  15. 88F350idi

    Anybody know where/how to buy just Caps or Olives

    I got mine from a local fuel injection shop that specializes in rebuilding injection pumps.
  16. 88F350idi

    Clutch Question

    ok thanks for your help guys
  17. 88F350idi

    Clutch Question

    Looking to swap my dual mass setup on my zf5 for a single mass flywheel and new clutch. mine is making a ton of noise when i start it up, the flywheel is junk. I'm looking for advice on what brand of clutch to buy. any help would be greatly appreciated. thanks.
  18. 88F350idi

    glow plug problems - truck down

    mine did the same when the plugs were shot, but be sure to test them before just replacing. i used a test light to test mine as well
  19. 88F350idi

    Head Gaskets

    Does anyone know what the difference (if any) is between head gaskets from a N/A 7.3 vs. factory turbo 7.3? If there is a difference, are they interchangeable? Thanks
  20. 88F350idi

    Busted Glow Plugs

    Thanks a whole bunch guys. Got them out tonight without much difficulty. Huge relief!
  21. 88F350idi

    Busted Glow Plugs

    Hello, Just wondering what you guys think, or if anyone has had much luck with this. I have a swollen glow plug stuck in my cylinder head and the little bugger broke off. The head has been removed from the block and is sitting on my bench. Do I need to remove the pre-chamber or something to get...

Latest posts

Forum statistics

Threads
91,376
Posts
1,131,349
Members
24,175
Latest member
RangerDanger

Members online

Total: 623 (members: 10, guests: 613)

Share this page

Top