Search results

  1. 6

    For sale 6.9 and ZF5 speed

    SOLD SOLD SOLD!!! Woo Hoo
  2. 6

    For sale 6.9 and ZF5 speed

    ttt
  3. 6

    For sale 6.9 and ZF5 speed

    Deal of the week.. A 1985 6.9 106,000 miles when pulled last year(been sitting on a stand) and a zf 5spd 4x4 from an 89 f-350. Has the pto on the side but the shaft is cut. Doesnt effect the tranny. I have the slave cylinder, flywheel and bolts etc for the tranny. the motor is complete from...
  4. 6

    1989 Dana 60 Front Axle from Dually

    I have a 89 D-60 4x4 front axle from a dually truck.. Axle was already cut out and is on the ground.. Nothing else with it(springs etc) does have the dually spacers still on it. I bought it thinking i could use it in my 78 4x4.. No luck sold the truck $500 located in 19401 in PA
  5. 6

    Zf 5spd from 89 7.3 diesel 4x4

    I'll sell it out right for $550
  6. 6

    84 6.9 Ford Diesel 106,000 Miles

    I have an 84 6.9 Diesel, its complete including the complete wiring harness from the truck under the hood. Ran well when pulled, was going to be used in another projectm but sold the project. Only thing i'm missing is the valve cover bolts on one side, took them off to check how clean it...
  7. 6

    Zf 5spd from 89 7.3 diesel 4x4

    I have a Zf 5spd from an 89 F-350 4x4 Worked well when removed. Did have a pto on it and pto shft is cut but still connected to trans. I have trans, flywheel and Slave cylinder etc.. Make me a good offer and its yours.. Located in PA 19401
  8. 6

    7.3 IDI in a '73-'79

    I'm building what you want right now, I have a 78 Crewcab 4x4 and i'm using a mid 80's Diesel crossmember that needs to be trimmed but will fit in the frame of a 73-79 truck. Once mounted to the 6.9 and lowered in place i can either bolt it in or weld it up. A 6.9 with a turbo and zf-5spd is...
  9. 6

    92 front clip swap befiore and after

    so was the swap the whole front clip plus the cowl piece?? ANd are the bumpers useable from the 92 or did the front frames change for the mounts?
  10. 6

    1985 CC Dually 4x4

    Whats the magic number to sell it.. Everyone has a price in there mind that they need to get. Whats yours?
  11. 6

    97 7.3

    Check to make sure the wires going to the CPS arent exposed and shorting out against the motor.. Just had the same thing happen on a 99 7.3 and had an exposed wire shorting to the motor..
  12. 6

    Looking for an DIesel Crossmember

    Mel does have one for me, but hasn't given me a time frame of when he might get to it. HIs first email in July said he had it with a price and could get it for me. :confused: So i thought i would see if anyone else has one out there for my swap. Unless mel has it soon??
  13. 6

    Looking for an DIesel Crossmember

    Anybody in the PA, NJ, DE area have a diesel front crossmember for sale or parting out a truck? This is the crossmember the motor is bolted to. Let me know what you have and a price
  14. 6

    7.3 From a Van for a swap

    Group i can pick up a PSD from a 96 Van, for my 78 4x4 Crewcab Swap, and was wondering if the Van Psd was different then the truck?? Can it be used? I also want to use a Zf-5spd behind it.. I'll assume the crank will accept a pilot bearing? Also anyone know any articles for a PSD swap..
  15. 6

    1986 - 6.9L with turbo,C6 trans & t-case $500 OBO, will seperate..Light fire damage !

    Let me know... How bad was the motor after the fire?? Any pics of it?
  16. 6

    Broken Exhaust manifold

    Group went to look at another IDI motor, and it has a blown out exhaust manifold, that went and coooked the fuel pump on the block.. anyone ever hear of this?? What causes the manifold to blowout? Castiron usually handles the heat well
  17. 6

    FREE STUFF!

    could you ship it to 19401 with greyhound under the bus like they do? Then t doesnt need to be wrapped
  18. 6

    1986 - 6.9L with turbo,C6 trans & t-case $500 OBO, will seperate..Light fire damage !

    ship the motor? could you ship the Motor to 19401 in PA?
  19. 6

    1986 f350/parts

    gonecrazy hows $35 shipped? joe
  20. 6

    Looking for Motor Towers/ Cross member

    typ4 thanks, but A guy already sent me the info on using the newer crossmember and it works.. Sent pics of it already during the install and what was needed. Anyone have a price for me yet on these pieces?? Joe
  21. 6

    Looking for Motor Towers/ Cross member

    are the 2wd and 4x4 crossmembers the same?
  22. 6

    Looking for Motor Towers/ Cross member

    mel what part of PA are you in? Shipping might not be too bad I'm building a 78 F-250 4x4 and want an IDI in it..No i dont want a cummins , i just a fan of the 6.9 and the zf5 spd i have waiting for it.. I just want to see if i can modifiy the crossmember to work with the 78 frame etc.. let...
  23. 6

    Looking for Motor Towers/ Cross member

    h20drx the sooner the better.. i want to start working on the project since i just got doe making my garage bigger i can start work on the project let me know
  24. 6

    Looking for Motor Towers/ Cross member

    towcat would like the whole crossmember and plates for my diesel conversion. So i have no gasser crossmember to work with.. I know Greyhound Bus has cheap shipping, you could ship the crossmember that way. Or see what shipping would be to 19401 thru ups or fedex ground joe
  25. 6

    Looking for Motor Towers/ Cross member

    What i would like to buy is the complete crossmember cut out from the frame with everything connected to it minus the motor and motor mounts. I have a 6.9 with motor mounts on it, i just need the crossmemeber and the plates the motor mounts bolt to.

Latest posts

Forum statistics

Threads
91,332
Posts
1,130,507
Members
24,134
Latest member
m2rtin

Members online

Total: 603 (members: 4, guests: 599)

Share this page

Top