Search results

  1. notenuftime

    Newbie with a broken truck! No start!

    If I am not mistaken there are three temp switches, the one we are talking about activates the cold high idle solenoid and shuts it off once the engine reach 100 and something. The others give you your temp readings in the cab and let you know when your gana have a melt down.
  2. notenuftime

    RPM guage.

    Thanks I will give it a go, looks dirty as heck right now anyways.
  3. notenuftime

    Newbie with a broken truck! No start!

    I had a similar issue with my truck part of it was the cold high idle not dropping off due to a bad temp switch cause high revs and rough running. check out your pump closely for leaks fuel on the valley pan, there is also a controller that selects front or rear tank should be mounted on the...
  4. notenuftime

    RPM guage.

    Does it have two wires coming out of it big looking nut?.
  5. notenuftime

    leaky injector line, hard start.

    I don't see any leaks coming from the lines, I can see fuel around the threads. going to pull them tomorrow and try reseating them. when I bought the truck it only had two sets of clamps on it could having no clamps on some of the lines cause them to leak at the pump?.
  6. notenuftime

    leaky injector line, hard start.

    I have had my new pump in for a couple weeks now truck runs great found a couple leaks tighten up and was fine. started the truck today and had a really rough start engine knock then went to idle and by the way its really cold out. after I got home today I popped the hood and found two lines...
  7. notenuftime

    RPM guage.

    sounds possible. just started working again this morning on the way to work.
  8. notenuftime

    RPM guage.

    My RPM dial seems to be about 500 RPM behind actual and when sitting at idle its all the way at zero any one got this problem I assume it warn out maybe, how may I go about fixing this.
  9. notenuftime

    cold high idle switch.

    my switch is bad I pulled the connection and it feel off before it was warm, just leaving it unplugged till I get a switch. Found out how to get people to stop tailgating me I just fill my truck with precariously stacked and bouncing lumber hanging out the back 50mph on the main road, line of...
  10. notenuftime

    cold high idle switch.

    yes I believe I found it, wired in with my glow plug harness has a clip connector on top right next to some radiator tube. I will get a new one after I check it out tomorrow, replacing is just unscrewing and putting in a new one right? nothin special.
  11. notenuftime

    cold high idle switch.

    where is the temp switch located I believe some where on the passenger side?.
  12. notenuftime

    cold high idle switch.

    would it be bad to drive like this till I figure out the issue, need to haul wood in a bad way.
  13. notenuftime

    cold high idle switch.

    Just put a new pump in my truck took a couple crack to turn over but is running great, I let it warm up everything seams good. my high idle solenoid arm is extended and when warm is not retracting could this be due to my low batteries charging up or does the arm stay extend to idle. When I put...
  14. notenuftime

    hard lines to pump.

    is it normal to have two to three threads showing where the hard line attaches to the pump, everything is tight just looks weird with the thread exposed.
  15. notenuftime

    injector pump cover permatex RTV?

    yes not the fuel screw, just got done putting it together looks good.
  16. notenuftime

    injector pump cover permatex RTV?

    thanks, its finally time to finish the rebuild foot of snow and building outside I need some 4wd.
  17. notenuftime

    injector pump cover permatex RTV?

    Do I use permatex RTV to seal the cover for my pump the one up front with the two bolts? just double checking.
  18. notenuftime

    injector line clamps.

    thanks for info probably going with the ones from ebay.
  19. notenuftime

    injector line clamps.

    I need a new set of clamps for my lines any one got a good place to get them from?.
  20. notenuftime

    Torque specs please?.

    Any one have the right torque specs for the drain and fill plugs for a zf-5, and transfer case i thought i heard 25-30lbs for both of them just not sure. Also are there any specs for front and rear diff bolts on the cover and plugs?.
  21. notenuftime

    Understanding coolant, coolant filters.

    I would like to do a full flush of my coolant system and add a filter, any one have good links or could fill me in on installation and flush.
  22. notenuftime

    arp?

    Turbo's are great but you can't drive them, you have plenty of time in life to put turbo's on all types of stuff. Biggest thing is tho short cuts usually end badly, my truck has been down for the rebuild for months in the end tho the wait is worth it knowing you have a solid truck.
  23. notenuftime

    valve cover removal.

    should be fun removing them this week. so there is no torque spec on the bolts? just snugged up.
  24. notenuftime

    valve cover removal.

    sounds like if i glue the gasket to the valve cover add a little to the head and bolts i should be good.
  25. notenuftime

    valve cover removal.

    i have come to learn my lessons with over tightening anything with a gasket, like large induction hardening filters with a couple hundred gallons of water behind them and only one place to go....all over me. Thanks for the reminder tho i think this is the first time the covers have been pulled...

Latest posts

Forum statistics

Threads
93,001
Posts
1,155,994
Members
26,589
Latest member
tke395

Members online

Total: 809 (members: 1, guests: 808)

Share this page

Top