Search results

  1. R

    A Post I Don't Want To Make

    The engine is not junked yet. Used piston & rod would be easy to access. Just have to have gaskets & sealer (for oil pan).
  2. R

    A Post I Don't Want To Make

    Bent rod. Mine sounds like that but runs. Was it hard to start/turn over the first time before the video. Mine cranks first time every time. Does not take much fluid to bend one, takes more to hydrolock. Compression tester time. Mine have been # 7 & or #8 cylinders
  3. R

    All the popups suck

    Same here with no ads or pop-ups.
  4. R

    92' with 45k getting a Gearstar tranny and rear main seal: what else should I be doing

    Degrease and wash that engine. Easy to find the leaks then & will be so much purtyer
  5. R

    Burnt out starter

    Low battery/bad battery cables if new one is not turning over fast. Will burn that new starter up fast!!
  6. R

    I FIX ONE THING, ANOTHER BREAKS... HELP

    Your fuel pump should be in circuit with injection pump FSS. Your fuel heater is probably shorting out. Disconnect the fuel heater altogether & see if circuit breaker kicks with just the e pump on it.
  7. R

    C6 slipping second gear

    Check the VRV setting & vac hoses.
  8. R

    One new tire

    Get a rubber o-ring for replacement that will hold the socket and slip some silicone grease on it. I use anti-seize on my lugnuts also.
  9. R

    Bronco Fuel Tank Install

    I have seen some other posts in the past where they used threaded rod to make up the difference on the Bronco tanks. The fill hose seems to be the biggest problem since the swage on the Bronco hose is larger and closer to the frame.
  10. R

    Bronco Fuel Tank Install

    Nice HARPOON job on that tank!!
  11. R

    Brake lights

    You may need to check the ground under the left rear frame. May have to clean & reconnect. I had do do this to mine for same reason.
  12. R

    Replacing head gaskets, what else?

    Right Stuff RTV on oil pan. Maybe check a rod/main bearing or 2 while pan is off. Check oil pump feed line for possible stress cracks. Replace block coolant plugs with drains. Replace block heater if not already done. Check all lifters/push rods/rocker arms for wear. If you have the bucks...
  13. R

    Which One Would You Pick for a Gasser Swap; 6.9, 7.3, or 7.3 PS?

    7.3 IDI & stud it, port the water jackets in the block & heads to fit the 6.9 gaskets, use 6.9 Felpro gaskets, while the heads are off//port them and upgrade the valves and springs, find a set of turbo valve covers. For the fuel economy.
  14. R

    Truck won't start with new starter/starter solenoid

    Pull the glow plugs and see if you can manually turn it over at the crank bolt. Sounds locked up. Mine ran excellently until water got in the cylinder. Finally got it to turn over after a few trys and bent 2 piston rods easily with the starter. cookoo:idiot:-Playme
  15. R

    Cleaning out the radiator

    3/8" NPT. Plug has a 9/16" hex head.
  16. R

    IDI guy needs help

    If I was up there, I'd love to help him out. Sorry
  17. R

    Replacement coil springs

    Try this: https://www.rockauto.com/en/catalog/ford,1991,f-350,7.3l+v8+diesel,1126606,suspension,coil+spring,7512 Cab & Chassis for dual wheels
  18. R

    4wd vacuum line

    Well Al Gore (from my state) would know a LOT about being 'reliable'. :backoff-Flame Thr
  19. R

    My dumba$$

    Gotta cut back on smokin' that stuff, it'll fry yer brain :bail
  20. R

    Had a strange idle sound...

    Get some Hotshot Diesel Extreme and pour in both tanks. 1/2 in each tank.
  21. R

    Truck Registration

    $115 annual here in Tn/my area.
  22. R

    Coolant leaking from...somewhere

    Remove valley pan gasket before removing heads.
  23. R

    Bus pulling to both sides

    & don't be afraid to fill in your city/state. Lots of help across the nation on this site!! Even folks from other countries are members here.:Thumbs Up:Thumbs Up
  24. R

    7.3 idi water in oil

    Put something over the air filter housing if not turboed. You may have water leaking in the intake pan otherwise
  25. R

    Hood to cowl seal

    Throw an old floor mat or something big enough to lay over the filter housing to keep the water out even with new cowl seal.

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,953
Members
26,579
Latest member
truckonfire

Members online

No members online now.
Total: 1,564 (members: 0, guests: 1,564)

Share this page

Top