Search results

  1. 1mouse3

    parallel turbos

    I made the lower support for the radiator, had to force it to be true. @ISPKI, The reason I dont think there will be a issue with air flow is the dual SHO fans. One did good on the brass radiator and almost never switched to high, with the aluminum one it would switch on a hot day. Since...
  2. 1mouse3

    parallel turbos

    I got the lower mounts installed... This sets the intercooling in a deceant place... So have know area to cut further now... All ducks are in a row, so the ac core can get put in place. I dont remeber the original r12 core being as small as this r134 one... Ether way time...
  3. 1mouse3

    parallel turbos

    I think these are the lower brackets for the intercooler...
  4. 1mouse3

    parallel turbos

    Yes its out a 7.3 superduty and no, I do not have thought of it restricting flow.
  5. 1mouse3

    parallel turbos

    Time has come to dig out the intercooler and re-re-fit it, to the core support... From the out side, it looks good and past cuts did not need much touch up... On the inside there is a little bit more that needs cut, and yes I had to cut the newish radiator.
  6. 1mouse3

    Self oil burning

    I have the heart ready to be pulled for transplant, need to wait on another hand. With this manifold out it made starter removal easy... And same on this side to get the cooler out.
  7. 1mouse3

    So what did you do with your truck today?

    Dont make fun of my tent... It make it through a storm... And came with a replacement a/c core, hope no nests where made in the intercooler over the past decade. Old girl got cleaned up good as well.
  8. 1mouse3

    Three legged animal...

    Since playing with mount bussing, the core support gets to upgrade past the fight club tournaments.
  9. 1mouse3

    Self oil burning

    Well the core support is removed and accessory brakets are off the engine, so is a start of getting the engine ready to be plucked.
  10. 1mouse3

    Parts becoming obsolete

    Before I make my run on the interstate in a vehical of unknow state, I will run back roads a few times to test it. When I ran back roads with snow white, I found the vaccum pump to be a issue. I put the serpentine belt setup on her with a custom saginaw pump install for the hydroboost. Well the...
  11. 1mouse3

    kubota d1105 looses prime running

    This has a manual gauge on top of the tank, it has a stainless steel rod in the tank with a plastic float.
  12. 1mouse3

    kubota d1105 looses prime running

    I did drain the tank some weeks back and this is some of what came out it. After cleaning the tank, it will run till the tank is empty sitting. So I had them use the machine near where it sits, it gave no issue being ran for about a hour. So tanks for the help given. This is the old fuel...
  13. 1mouse3

    So what did you do with your truck today?

    Thanks and good catch, you cant find the weak point without trying. Still need to find a tackle block rated for at least 750lb, so the cable dose not drag on a shap edge. I put added support on the underside as well.
  14. 1mouse3

    So what did you do with your truck today?

    Old girl no longer has a questionable mount.
  15. 1mouse3

    Three legged animal...

    I started by getting the rowdy dump pipe out the way... This made it easy for me to get up here with the saw, and still beat up my knuckles... The primary issue with using a saw is rubber, it dampens motion and heats up the blade. Had to dice up the rubber a bit, so that can cut the...
  16. 1mouse3

    Three legged animal...

    This round starts by fixing this gap, that the corner one did not pull tight... So got them drilled out and corner bolt added, only the corner one was found to have a gap issue. So rivets back in... But the holes are now too big for the rivets... So a 1/4in bolt to fix the...
  17. 1mouse3

    Crawl mode lock out

    and a e40d... I dug around seeing if can find any clues and found this, there is not a lot on the 1345 over the 1356 that seem to be more common. I found that there was two differrent adaptors used and I have the misfortune of having the first one. adaptor 13-01-066-902 adaptor 1301-566-010
  18. 1mouse3

    Crawl mode lock out

    Was needing a usable shifter for the bw 1345 that came with the t19 and this caught my eye. This would moves like a normal shifter, over the weight check of the aluminum ones. This is the one that came with it... I had to poke a hole for it and this one is in better placement with the...
  19. 1mouse3

    Another lift pump lets me down.

    That is partly way the return on my 6.9 is the same size as the feed and way there is a cross for the caps to drain to tank, -05 hose is not a option. I dont have a issue with my caps being a snake but that is how the hoses wanted to be losse fit when I did it 10 years ago, and when I got it...
  20. 1mouse3

    ardunio madness

    Just a tease, nothing more...
  21. 1mouse3

    So what did you do with your truck today?

    Being able to stand it on end is nice, since gives direct access to the blade and drive parts.
  22. 1mouse3

    So what did you do with your truck today?

    This one dose have comet on the front, would like to find the seat pad for it but am probably going to have to make one my self. I like them since there small and easy to work on.
  23. 1mouse3

    So what did you do with your truck today?

    I think you pick the wrong person out the line up. This one is closer, but still not the same. I dont think this one is it ether.
  24. 1mouse3

    So what did you do with your truck today?

    Your missing this plate on the front... :sly
  25. 1mouse3

    So what did you do with your truck today?

    I have got the bass boat a fair bit done and getting close to the point I can cristen her back on to water. :joker: Its down to nick nacks and the mount busings on the driver side, then can swap the engine for one cobbled together.

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,945
Members
26,578
Latest member
dogdanblue

Members online

Total: 1,458 (members: 8, guests: 1,450)

Share this page

Top