Search results

  1. rewbrooks50

    7.3 IDIT are suppose to leak

    Could the injector be clogged causing pressure at the IP?
  2. rewbrooks50

    7.3 IDIT are suppose to leak

    I have ordered a new steel line from Diesel Stop on eBay and an emergency line from Accurate Diesel. I tried three different lines. And another fitting in the IP. I tighten at the pump first then the injection connection. Same results. I tighten much as could. We will see what the new parts do.
  3. rewbrooks50

    7.3 IDIT are suppose to leak

    I received a used injector line and IP output fitting from Wes today. I installed both parts and it still leaks. Do I need to get a brand new line that has never been installed or seated?
  4. rewbrooks50

    7.3 IDIT are suppose to leak

    I replaced all the lines about 3 years ago from Accurate Diesel. This is the first problem I have had.
  5. rewbrooks50

    7.3 IDIT are suppose to leak

    My inlet line from the filter head to IP is not leaking. My leak is the #4 IP to injector line at the IP outlet fitting. Are any seals that go into the nuts? I don't think so. The second picture is the end that is leaking. I cleaned the ends and did not find any deep cuts in the olive...
  6. rewbrooks50

    7.3 IDIT are suppose to leak

    I put a small ac o-ring on the line between the nut and olive. Still leaking and maybe more. I couldn’t get the line fitting out of the IP to check the seat. It is leaking where the steel line goes into the nut fitting. It can only be the steel line or the inlet fitting on the IP. Suggestions...
  7. rewbrooks50

    7.3 IDIT are suppose to leak

    Tighten the nut and replaced the pipe with the old one I had on hand. Still leaking at the IP. Is there any thread sealer or tape that can be used? Or, can the fitting in the IP be bad? What is the replacement part?
  8. rewbrooks50

    7.3 IDIT are suppose to leak

    It the second line from the front of driver side. It’s dripping at the IP end. I will try to tighten it tomorrow with a line wrench. Thanks for the replies.
  9. rewbrooks50

    7.3 IDIT are suppose to leak

    Seriously, what size is the IP line nut? Is there a special tool to reach to tighten? Any parts needed to repair the leak?
  10. rewbrooks50

    7.3 IDIT are suppose to leak

    My 94 F250 always has a leak somewhere. Added 6.0 trans cooler and leaked after a few days. Removed the front grill and support and bumper three times to stop the leak. The oil pan plug leaked. Wes sent me a new one. Fuel rubber lines to the electric pump leaked. Then the water pump started...
  11. rewbrooks50

    Quick turbo question

    I like that video! Oh that’s my rig.
  12. rewbrooks50

    Quick turbo question

    The glow shift MaxTow gauges are not recommended by most; but, they are working great for me. And, my wife thinks she is in the cockpit is a 747. The white face on the original gauge panel are a stick-on decal. Can be purchased on line, like amazon. Matched my other gauges. Sent from my...
  13. rewbrooks50

    Intercooler

    Did you install the cooler without removing the condenser?
  14. rewbrooks50

    Loose column SHIFTER even w/ tightening bolts and replacing bushings - SOLVED

    Thanks
  15. rewbrooks50

    Intercooler

    My neighbor does welding. We made lower mounting brackets with one inch square tube and one inch angle. It fits the lower intercooler insulated mounts. Same as on the stickies above.
  16. rewbrooks50

    Intercooler

    Not sure what size I have. Mine is between the intercooler in front of the ac condenser. The brace for the front support is in front of the trans cooler.
  17. rewbrooks50

    Intercooler

    6.0 trans cooler install sticky: http://www.dieselstorm.com/docs/trans_cooler_upgrade_install.pdf
  18. rewbrooks50

    Intercooler

    I followed this sticky. http://www.fourdoorbronco.com/board/showthread.php?4603-6.0L-intercooler-install-in-92-96-body
  19. rewbrooks50

    Loose column SHIFTER even w/ tightening bolts and replacing bushings - SOLVED

    Did the bushing correct the starting in park issues?
  20. rewbrooks50

    Intercooler

    I have all 4 installed. Radiator, condenser, 6.0 trans cooler and intercooler. The trans cooler and condenser are real close. I put rubber insulator in between them. I live near Dallas Tx and water is very consistent at 195 with ac on. I have not towed 13k lbs RV yet.
  21. rewbrooks50

    Intercooler

    I installed a 6.0 intercooler and transmission fluid cooler in my 94 IDIT. Minor modifications. Works great.
  22. rewbrooks50

    driver side door lock issue

    Not sure; but, it could be the power lock motor/actuator. Mine works sometimes and not. That might move the linkage out of the way.
  23. rewbrooks50

    PSA on CDD Phone Line

    Get well soon!
  24. rewbrooks50

    Anyone using new Banks, Hypermax, R&D, or home made turbo kits?

    And it was upgraded by typ4.
  25. rewbrooks50

    Anyone using new Banks, Hypermax, R&D, or home made turbo kits?

    I second this. Wes rebuilt my turbo and IP with upgrades. The new power is amazing.

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,108
Members
26,430
Latest member
Brownlee5212

Members online

Total: 807 (members: 3, guests: 804)

Share this page

Top