Search results

  1. 3Kp

    Iso TransCase linkage

    I don't have the lever anymore. Have you tried local junk yards?
  2. 3Kp

    Iso TransCase linkage

    What I circle in red is what you need
  3. 3Kp

    Iso TransCase linkage

    Shifter lever is gone. I'll check the linkage in a few days when I visit my in laws again. It's out at there house.
  4. 3Kp

    Looking at buy 6.0 possibly

    It's in Ohio. 10hr bus ride. Believe it said 4+hr drive time.
  5. 3Kp

    Iso TransCase linkage

    you still looking for the linkage? Do you have a picture of the linkage you are seeking? I have a E40D I pulled out of a 94 idi It may still be on it.
  6. 3Kp

    Looking at buy 6.0 possibly

    Thanks DaveBen. I at one point in time had 5 idi's at once. I still have my crew cab in my avatar. Which is going through a rebuild process. Taking it down to frame, swapping to a DT360, still in the air on which tranny (auto or manual) if I stick with the auto it will have a Allison 6spd...
  7. 3Kp

    Looking at buy 6.0 possibly

    I found a 04 with 6.0 no rust at all, one owner, 6sp 4x4, with 198K miles. Was told motor is still all stock. It's a basic model with bench seats, window cranks, it does have AC and cruise. they're asking $9K for it. I don't know much about the 6.0 except horror stories. Do you think this...
  8. 3Kp

    Radiator Cleaning Question

    It was a Stock radiator.
  9. 3Kp

    84 F 250 Wire issue

    Originally had 6.9 system. Which worked part time then quit! So he's just gives a like squirt of ether. Been that way for months!
  10. 3Kp

    84 F 250 Wire issue

    Wire harness has been cut out. They are spliced together. This is a wiring mess!
  11. 3Kp

    84 F 250 Wire issue

    Think I'm going to run a dedicated wire from the battery to a switch in the cab with a in line fuse out to the IP. So we can get it and going for a while. I just need time to finish building my gantry so I can swap engines out of the 89 and put in my 94 (94 motor is toast) Then was going to...
  12. 3Kp

    84 F 250 Wire issue

    My sons truck stopped running yesterday on his way home and left him stranded on the side of the road. I did some investigating today when I had a chance and found that the wire that goes to the top of the Injection pump has no power which killed the truck. (yes it's not a fuel issue, it's a...
  13. 3Kp

    Freeze plugs

    Are you just doing the heads. Then No. My block has to be bored due to a big pit I have in it. So the shop I talked to said he going to bore it and hot dip it, To be sure the channels/ports are free of debris is if he pops out the freeze plugs otherwise he will not do the job. Here is the...
  14. 3Kp

    Freeze plugs

    The thing is I'm not sure what the tool looks like. He could hold up funky tool and say its it. Anyone have any idea what this special tool looks like?
  15. 3Kp

    Freeze plugs

    Odd this came up. I called a machine shop here local. He did he wouldn't touch my motor vehicle with out pulling the freeze plugs. Going to have it bored and hot dipped. He said he can't properly clean the channels out with them in. Said he doesn't buy that cheap Chinese crap! Lol
  16. 3Kp

    Which is better to build and why?

    Tonight a decision has been determined. After attempting to hone the cylinders one has a big as pit in it. So with that happening going to build the 6.9 motor.
  17. 3Kp

    Which is better to build and why?

    That's a good possibility not sure how it was stored before I got it. It was up right when I brought it home/in-laws since they have a garage I can use.
  18. 3Kp

    Which is better to build and why?

    Thanks Scott. Travis was over here last week to drop off a tool set so I could get stripped bolts out. We were talking about that place but I didn't ask where it was. I have 3 sets of head that need attention.
  19. 3Kp

    Which is better to build and why?

    I was hoping for your input since I believe you have a built 6.9 Travis was impressed with a machine shop in Greenfield think I'll probably give them a shot. If I don't have a fuzzy feeling may ask you for the info on the one you used. It's about 2.5-3 hrs away one way for me
  20. 3Kp

    Which is better to build and why?

    Let's say hypothetically both engines were the same condition? Sorry never built a motor before what do you mean by mag the heads?
  21. 3Kp

    Which is better to build and why?

    South side Indy. I did know the wall thickness and studs were different. Just not sure if I built the 6.9 I could achieve my goal at towing capacity
  22. 3Kp

    Which is better to build and why?

    Going to give a little history/story of my issue. I have a 94 Idit motor that blew up (not sure if its savable yet, doubt it!) I trades a set of fenders for a 6.9 unknown condition of the motor to put into the 94. I decided to break the motor down to reseal it before putting it into the truck...
  23. 3Kp

    2017 Oilburners Rally

    Not sure if we're going to be able to go either. Trucks keep breaking down and engines blowing up here. Can't get ahead of the 8 ball yet!.
  24. 3Kp

    Weight of a reg cab?

    Thank you for the responses. It's XL cab complete with seats and glass still. Didn't pay attention for AC. I was concern about the trailer to be able to carry it as well since I'm borrowing one from a friend.
  25. 3Kp

    Weight of a reg cab?

    My son is going to purchase a regular cab to replace his, We found one but we were curious on how much the cab it weighs. It will be complete with all trimmings and glass. They are going to load it for us with a boom. But trying to figure how were going to get it off with out damaging it or...

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,105
Members
26,430
Latest member
Brownlee5212

Members online

Total: 940 (members: 1, guests: 939)

Share this page

Top