Search results

  1. quickster

    84 6.9 idi injector pump disassembly

    Save your $$$ and look for a rebuilt pump if that is what you think the problem is. Check the fuel filter You'll be surprised seeing all the crap in there.
  2. quickster

    Major Setback

    Sorry for your loss.
  3. quickster

    Pulled a 1987 out of a hole

    Yeah I did the glowshifts w/pillar and I like it. Keeps everything off to the side. And if you add it up the glowshift is probably the cheapest option if you're going for 3 gauges.
  4. quickster

    Airbags or Timbrins,and a few other questions

    Hey Goat, I picked up the skid steer from up north and did not get pulled over once. I used a plate off my neighbors trailer did not get pull ed over. The truck ran good, but it was the reason I did the turbo install. I bought the timbres thinking I could throw them on and be good to go. But...
  5. quickster

    Starting an 093 turbo install on my 91 F350

    Too late. When I finished up the turbo and installed the gauges I took it out and pulled the trailer with arond 5-6 tons of stone to see how it went. It pulls great, but the trans temp got up to around 200-205 degrees and that made me nervous. So I went and put another cooler in line with the...
  6. quickster

    New to me f350 what to do

    Man get something on there. If you need an air cleaner assembly I have one. It must blow dust instead of exhaust.
  7. quickster

    Half-azzed paint job advice?

    I painted the truck in my sig 2 years ago in my garage. I used a HB gun and my crappy compressor. Did minimal bondo, eliminated the fender markings,(F250). Left all the dings and dents. Paint cost 450 from Sherman Williams auto. Urethane , no clear or anything else. Wash it up and it looks as...
  8. quickster

    Starting an 093 turbo install on my 91 F350

    I read about the Banks trans command, and how it changes the shift points. I don't know if I can get the short shifting out by adjusting the tps. Before the turbo it used to run out in every gear. Can't wait to see how it runs with the fuel up a couple flats.
  9. quickster

    Starting an 093 turbo install on my 91 F350

    The dang egt gauge on startup is at 150. I have tocallglowshiftto see if there is a way to zero the needle. And the pickup is in the crossover pipe.
  10. quickster

    Starting an 093 turbo install on my 91 F350

    I seen 2 maybe 3 psi. And that was at 2500 rpm. But like I said it shifts so quick now I haven't wound it up in any gear yet. I turned off the od and wounditup a little in third and it got up to 55 60 and I couldn't even tell if it was running at 1800 rpm or 3000 rpm. It was so quiet. But I'm...
  11. quickster

    Starting an 093 turbo install on my 91 F350

    So the day finally came. I bought a stock 93-94 airbox because I'm not going to go and try an aftermarket setup at this stage of the game. I need the truck for work and I have no time to putinto this anymore. So I took her out for a test drive and man is she quiet. It used to drone being...
  12. quickster

    1989 F-250 7.3 Project

    Also I'm running 235 skinnys.
  13. quickster

    1989 F-250 7.3 Project

    Don't bother. We have leaf springs, so tighten stuff up. Or you can do what i did, that is air down. Around here we have some dirt roads, so I went 35 psi front and 50 rear. That really works. When I pull the dump trailer I'll go up in pressure.
  14. quickster

    Knock please help

    Looks like the injector was only a couple turns in. Damn.
  15. quickster

    new gauge,no boost

    I actually did it while the truck was running and it didn't move. I'll try again tomorrow. But at least I'm getting boost.
  16. quickster

    new gauge,no boost

    the inlet is pretty tight. I loosened up the jam nut thats against the housing and it barely moves.
  17. quickster

    new gauge,no boost

    So I went outside and ran the truck with the boost line in some water. I bubbles up so I'm getting boost. I don't see how turning the inlet will get the gauge to move. Inlet is on the bottom of the gauge so I don't think I mcan rotate it. My stupid iphone won't send me the pic I took to show...
  18. quickster

    new gauge,no boost

    Thanks. I was just going thru old threads and seen where you mentioned that. I'm going out now to give it a shot.
  19. quickster

    new gauge,no boost

    Hey all, I installed a boost gauge and I'm not getting any reading. There are no exhaust leaks, and the snail is tight. It's a glowshift gauge with the hard plastic line .I have it plumbed into the snail, and used teflon tape. Still not getting any reading. Turbo spools up nice, and like I said...
  20. quickster

    Parting 1994 7.3 IDI TURBO engine

    That's the right one. That and the dipstick and tube. Let me know how topay and I'll get youmyaddress. Thanks
  21. quickster

    Parting 1994 7.3 IDI TURBO engine

    Hey. What's the status on the parts? I will taketh airbox and trans dipstick and tube . Just wanted to see if the box was correct. Let me know
  22. quickster

    Parting 1994 7.3 IDI TURBO engine

    Thanks for getting back. Is it the j style, 93-94?if you can send a pic to [email protected]. if it's the correct one I'll take it off your hands.
  23. quickster

    hissing sound after shutdown

    Those vacuum lines tend to rub on parts and get worn thru very easily. Air filter cover did it to mine.
  24. quickster

    Parting 1994 7.3 IDI TURBO engine

    Air cleaner assembly if you have it. Thanks
  25. quickster

    1994 IDIT parts or complete F350, CC, 2WD, E4OD Only needs a head gasket to run.

    do you want to part with the air cleaner assembly? And I'm in the market for the trans dipstick and tube . Just did a 093 turbo install

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,105
Members
26,430
Latest member
Brownlee5212

Members online

Total: 790 (members: 3, guests: 787)

Share this page

Top