Recent content by Jbone36

  1. Jbone36

    "Video" whats this sound bad starter?

    If I crank the pulley with a socket wrench it's hard to turn but can get about one pull or about 3 inches on wrench after that will crank over maybe one revolution and then stick again..very very loud. https://streamable.com/1gkauf
  2. Jbone36

    Too much fuel filtration, microns and WMO

    So my original water separator was leaking air, replaced with goldenrod water separator running after a seachoice electric pump. Im debating installing another filter of smaller micron either before fuel pump or after at the IP. Im planning on running wmo in the coming months. How much...
  3. Jbone36

    Electric fuel pump wont push gas unless engine cranking?

    BTW that what i meant pressure not vac..but like im saying if there is too much pressure to move fuel to injectors then whats the point of people saying to cylcle pump before glow plugs solves air intrusion hard start,?
  4. Jbone36

    Electric fuel pump wont push gas unless engine cranking?

    So how does everyone hook up an electric pump to solve air intrusion if it does exactly the same thing as mechanical?
  5. Jbone36

    Electric fuel pump wont push gas unless engine cranking?

    Im holding it to positive and negative of battery..when i unhook the outlet off of injector pump it pumps plenty of fuel but hooking it up to injector pump inlet it stops because of vacume? Only lets fuel in when cranking engine.
  6. Jbone36

    Electric fuel pump wont push gas unless engine cranking?

    Sick of air intrusion coming and going trying to hook up facet pump. Ive heard people say in message board you can hook up electric and pump fuel while waiting on glow plugs to cylcle. Well unless im not cranking engine fuel wont move.what am i missing here?
  7. Jbone36

    Can i put old DMF back in after installing SMF?

  8. Jbone36

    Can i put old DMF back in after installing SMF?

    Exactly whats happening although its not random its all times over 55mph and super loud at 60.
  9. Jbone36

    Can i put old DMF back in after installing SMF?

    Its not possible to be motor mounts right because flywheel cant move. Its almost like when i let off gas the flywheel is spinning on clutch or metal..instantly goes away no mater speed if accelerate or push in clutch..Im perplexed.
  10. Jbone36

    Can i put old DMF back in after installing SMF?

    Everything was fine after i swapped the e4od for zf5 until front driveshaft came off at high speed "diddnt know it got bumped into 4x4 snapped of hit frame and snapped tail section..replaced tail section and also went to smf. After replacement i have the sound when there is a load is let off of...
  11. Jbone36

    Can i put old DMF back in after installing SMF?

    Goes away when clutch is pressed its a loud metal on metal from bell housing like flywheel is spinning rubbing or pushing transmission too hard
  12. Jbone36

    Can i put old DMF back in after installing SMF?

    Hate to beat a dead horse or open a can of flywheel politics but.. A while back snapped the tailhousing on zf5 decided while in there to do the clutch " worked fine though". After some reading i went with LUK SMF. This thing is loud . And its making me nervous that its killing my trans. When...
  13. Jbone36

    Zf5 manual Replace tail housing w transmission in truck.

    After more research theres no way for the sake of time, lack of tools and location of truck i can pull off a full rebuild of transmission. Prewty surw springs would fly off into the bushes. But... If you check out this video at 4:35 when the casing is slipped off. My thoughts are i can find a...
  14. Jbone36

    Zf5 manual Replace tail housing w transmission in truck.

    Thanks for the reply. Yea decided to just pull it out and figure it out with a rebuild manual. Its gotta get put back together and work eventually.
  15. Jbone36

    Zf5 manual Replace tail housing w transmission in truck.

    Doing more reading, yes it seems trans has to come out being rear loaded transmission. So because everything is attached inside but is there a way to slide it out remove rear alan bolts attaching inside assembly and replace rear tail? Or will the whole thing explode if i try?
See more

Latest posts

Forum statistics

Threads
91,262
Posts
1,129,489
Members
24,091
Latest member
freqencyheight

Members online

Total: 571 (members: 4, guests: 567)

Share this page

Top