Forums
New posts
Search forums
What's new
New posts
New resources
Latest activity
Resources
Latest reviews
Search resources
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
david85's latest activity
david85
replied to the thread
Cup holders
.
It’s also a welcome distraction from the times we live in. I’m seriously considering those inserts that were shown earlier in the...
Yesterday at 10:00 AM
david85
reacted to
Jesus Freak's post
in the thread
Cup holders
with
Like
.
Yes, it's very important that we consider our cupholders. One way to gauge their importance is to observe the longevity of this thread...
Yesterday at 9:54 AM
david85
reacted to
CDX825's post
in the thread
Best radiator hose clamp?
with
Like
.
Everyone like to junk the spring type clamps used from the factory but they are the best because they keep constant tension on the hose...
Wednesday at 7:01 PM
david85
replied to the thread
Cup holders
.
My mid 80s E24 didn’t even have cup holders. Instead, you had a cooler between the rear seats with a molded liner to secure 3 cans of...
Wednesday at 6:30 PM
david85
reacted to
gretatuneberg's post
in the thread
Self regulating glow plugs
with
Like
.
I know autolite gets a bad rap sometimes but I have a manual push button system and have had great success with the autolite 1115 self...
Wednesday at 11:07 AM
david85
replied to the thread
Self regulating glow plugs
.
I’ve been running the autolite 1115s as well for a couple years with no issues. I bench tested each of them for one minute before...
Wednesday at 11:07 AM
david85
reacted to
KansasIDI's post
in the thread
Self regulating glow plugs
with
Like
.
Well with most stuff being, ah, outsourced, to, uh, China, and what with them being able to make whatever quality you requested, and...
Wednesday at 11:01 AM
david85
replied to the thread
Double Cardan Front Driveshaft Parts
.
I ended up just ordering a whole drive shaft. The old one was too far gone.
Wednesday at 10:55 AM
david85
reacted to
03wr250f's post
in the thread
e locker 10.25
with
Like
.
been wanting a e locker for several years now, And finally got around to it! made a short video about it as well
Tuesday at 11:18 PM
david85
reacted to
03wr250f's post
in the thread
e locker 10.25
with
Like
.
Tuesday at 11:18 PM
david85
replied to the thread
e locker 10.25
.
Nice job! As I mentioned on the other thread, the factory bulkhead connector is probably not worth the trouble. Using a heat shrink on...
Tuesday at 11:18 PM
david85
reacted to
03wr250f's post
in the thread
Factory Ford E-Locker Install
with
Like
.
love it, just did the same on mine, and basically have seen all the things you have. the starboard was a nice touch!
Tuesday at 10:40 PM
david85
replied to the thread
Factory Ford E-Locker Install
.
If I were to do it again, I’d probably just pass the wires through the gap for the gasket, with a couple of notches carved into the...
Tuesday at 10:39 PM
david85
reacted to
Cubey's post
in the thread
U-joint warning chime
with
Sad
.
When I found it bad that morning, just before getting on the highway towards a bigger city in Colorado, from Laramie WY and having the...
Sunday at 2:46 PM
david85
replied to the thread
U-joint warning chime
.
I’ve been lucky so far. Never had a center support bearing fail. I wanted to swap in a single piece driveshaft but was told by one shop...
Sunday at 12:35 PM
Latest posts
Injector precups
Latest: gator1211
Yesterday at 10:31 PM
6.9L IH & 7.3L IDI Diesels
CDR Valve.
Latest: Kdo58
Yesterday at 10:22 PM
6.9L IH & 7.3L IDI Diesels
R
Starting an 093 turbo install on my 91 F350
Latest: Rocknit4x4
Yesterday at 4:06 PM
6.9L IH & 7.3L IDI Diesels
Cup holders
Latest: Rdnck84_03
Yesterday at 1:55 PM
6.9L IH & 7.3L IDI Diesels
Removing VE-pump anti-tamper cover w/o damaging it?
Latest: bob_442
Yesterday at 12:48 PM
1st Generation Cummins
Forum statistics
Threads
91,284
Posts
1,129,785
Members
24,099
Latest member
IDIBronco86
Members online
Minuteman96
MethrenBlifs
JourneymanD
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top