hey guys and gals ive got a buddy with a problem he has a 05 sd with 115k on clock all stock it has just started knocking in the top of engine on the pass side and white smoking bad. i can say he more than likely has egr problems but what would cause the knock it only does it when up to...
got a buddy with a 97 f250 4x4 250k on clock service reg at 6k all of trucks life. no problems until today truck ran just fine shut it off and no start i checked it out and cranks good tach comes up to 500rpm when cranking but no start no smoke out of tail pipe either. tach does not bounce when...
i have for sale a 1985 f250 ext cab 4x4 with 6.9l auto c6 old truck need glow plugs toggle switch got left on. the truck is kinda rough it needs heater core and a good cleaning it also has som rust on the bed and on the cab it is brown and tan in color, it has pdl an pw sometimes work. it runs...
ok so you guys were right about power adders and a stock clutch didnt have my chip in for a week and smoke my clutch i havent tore it down yet but i have done a bit of price checking. i have a question will my truck have a solid flywheel or a dual mass one i am getting conflicting reports from...
just ordered a set of glo shift guages and to get the best deal i had to go with a 3 guage set i got boost egt and oil temp i dont have a auto tranny so no need for trans temp i was wondering where to tap in to get engine oil temp. and is there a fitting i can take out to get boost pres instead...
i am wanting to convert my single wheel truck to duals how is the best way to do it are the axels the same in the back or are the dual wheel trucks wider and are the spring peches the same on both if they are wider also on the front is it the same with a different hub or a totally different...
my truck has just started to get hard to start it is 40deg+ in the mornings i can cycle the key of and on 4 or 5 times each time letting the wait to start light to go off and then it will start and white smokes allot whith a hint of blue and runs kinda rough then iclars up after a second and...
im working on a 2000 3500 5.9 6spd the truck will blow the 20amp ignition fuse in the dash it wont do it all of the time but it is getting worse i have checked all of the wirring to the starter no problems im thinking it may be the starter but not sure anyone had this problem?
well i took the muf and cat off my truck saturday did not see much improvement on hp or torq but i havent hooked it to anything yet, did notice a big improvement in sound you can actually hear the turbo now i was wondering if the psd have a silencer ring on the turbo like the cummins do. also if...
i hav a question about my truck it is a 2001 f250 7.3l 6spd 4x4 my question is if there is any way to check if i have a locking diff without taking the cover off, the build sheet says that it is but yesterday just about stuck it and only on wheel was pulling. also on the 4x4 what direction do...
i have a 2001 f250 sd 7.3l man 6spd 4x4. It seems to be leaking from the lower radiator hose elbow that comes off of the engine it looks to be coming from the flange that bolts the two elbows together . my question is if there is a gasket on this flange or if the bolts could just need...
i was just on napa website and found some exhaust pipes for 7.3l i was wondering if these will work on my truck i am wanting to delete the cat and muf without spending much cash.
my truck 2001 f250 xl 7.3l 4x4 6spd excab longbed.
i am thinking of buying some power adders for my truck i would like to get some feedback on the things i am looking at.
1st mopak 5" exhaust no muf
2nd afe stage 2 pro guard 7 air filter
3rd edge juice with attitude
2001 psd 4x4 ext cab 6spd all stock 90k
any info...
just bought new truck 01 sd 6spd 7.3 it seems to have a cat converter is this what i am seeing or something else i am wanting to run staight exhaust will this hurt anything if i take the muf and converter off.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.