Search results

  1. S

    Gear Rubbing Inside of Manual Hub

    1993 F250 7.3 NA with Dana 50 and manual locking hubs. I just replaced rotors, calipers, brake pads, and bearings/races. When I put the hub back together on the passenger side the larger gear that is inside the hub body/ backed by a spring and held in by a small Phillips screw is rubbing and...
  2. S

    Blinking Fuel Filter Light

    Howdy, hope everyone is running well. Made it to Oregon from Texas, pick up ran really besides vacuum pump going out in Nevada and then until two hours away from my destination. Kept Egts below 800-900 the whole way usually around 500-600. Have recently installed baby moose injection pump...
  3. S

    Extender for Injector #1

    I know this has been discussed before but at least from the posts I saw the only options were finding one of the lines off a van or classic diesel designs used to sell them but does not anymore. Got a baby moose fuel injection pump, installed, runs great but was leaking out of/around injector...
  4. S

    Mystery hose

    1993 7.3 idi N/A Howdy hope everyone is running well. I have a seemingly broken off 5/16th or 3/8th hose, one end is on a little panel with some other hoses connected to it the other end I have no idea where it’s supposed to go and can’t find any valve or anything that it should go to or can...
  5. S

    Oil dipstick tube

    I know there are some posts on this but need some clarification, trying to get back on road and to work. Was replacing valve cover gaskets and windshield wiper motor (along with a few other pita’s) upon removing mount for dip stick tube the thing just clunked right out of wherever it is...
  6. S

    Torque Specs for U-Bolts and Leaf Spring Bushings

    1993 7.3 idi f250 4x4 Dana 50 I have just about finished replacing the bushings for all of my leaf springs, including the rear, rear shackles. But can’t find for sure what the torque specs are for u-bolts or bushing bolts and would like to get those correct before I hit the road. If you have...
  7. S

    A/C compressor install

    Have a 1993 f250 xlt 7.3 non turbo Recently my a/c had a massive leak due to hose hanging too low on my intake and it burnt/melted through the hose. Wasn’t too concerned about it as don’t use the ac much and figured I’d fix it next summer until I started getting a nasty squealing and burning...
  8. S

    Hard Fuel Line possible adapters/connections

    Howdy, was wondering if anyone knows what kind of connection or fitting I could put on the end of this fuel line so I could go from this to a 3/8th hose. A 5/16 hose fits over it pretty snug but the 3/8th has a lot of wiggle room.
  9. S

    1993 F250 7.3 IDI fuel return line to tank

    Does anyone know where I can find a replacement for the return line that goes from fuel injectors to the tank? It runs along the frame. I have a hole and significant leak in mine right as the line meets the frame, further down from the 3/8 hose that is connected to housing on left side of engine...
  10. S

    1993 F250 7.3 IDI injection pump

    Have a 1993 7.3 idi (non turbo). I bought the pick up recently, ran pretty well when I first got it, started having some problems with it, some I have worked out but I think I’m still having a serious fuel delivery problem. These two forums pretty accurately describe what’s going on with it...
  11. S

    1993 F250 7.3 IDI non turbo Piston rings

    Howdy. Thanks to everyone on this forum have helped me out a lot already. I recently purchased a 1993 7.3 idi non turbo as my first diesel vehicle. (Odometer is out and both me and previous owner have no clue what that mileage is. Dumb move maybe, but she is very fun to drive) Drove from...

Latest posts

Forum statistics

Threads
91,311
Posts
1,130,171
Members
24,121
Latest member
720Diesel

Members online

Total: 385 (members: 2, guests: 383)

Share this page

Top