Search results

  1. J

    Sterling 10.25 oil leak

    Hello all ! looking for some help to fix an oil leak on a Sterling 10.25. I noticed a couple days ago Its leaking oil around where the U_joint is. I'm not familiar with these so Im not sure what seals are involved with repairing this. Thanks!
  2. J

    "Diesel" emblem

    Hello all. I posted this in the wanted section but figured I would post it here as well in case somebody didn't look down that far. Looking for the OEM "Diesel" emblem that mounts under the drivers side headlight. I can find every other one except for that one. For the 91. Appreciate the help!
  3. J

    ISO "Diesel" emblem

    Hello all. Anybody have the "Diesel" emblem that goes under the drivers side headlight they want to part with. I can find every other one except for that one. Going on a 91. Thank you
  4. J

    New Seats

    Hi all! I am finally going to install some used King Ranch seats, I picked up 6years ago, into the my 91 CC. Going to replace the carpet at the same time and just try to clean up the interior in general. The new seats are power as well as heated. My question is what do you guys think is the...
  5. J

    Making the change over to Hydroboost.

    Hi all! Im looking to convert over to hydroboost and wondering if there are any new units being made and if they are worth a darn. I have the power steering reservoir with the return port so I dont have to source that. Also planning to use the proportioning valve. Thanks for the info
  6. J

    Excessive Blowby/Crankcase pressure.

    Hi all. Looking for some input on my current problem. I have a rebuilt motor with about 32,000 miles on it(truck in my signature). The problem I'm experiencing is, in my opinion, excessive oil in my intake coming through my breather tube. My Crankcase is vented via passenger side valve cover to...
  7. J

    WTB IDIT OEM harmonic balancer

    Looking for the IDIT specific oem harmonic balancer for engine project. Thanks
  8. J

    Turbo rods and pistons

    I would like to run factory turbo rods and pistons in my n/a block. Will I need a different harmonic balancer and flywheel? i heard they used a differnt balancer and flywheel on the factory IDIT motor .I'm planning on having the entire rotating assembly balanced as well. Thanks!
  9. J

    IDIT piston pin bushing

    I have a set of turbo rods I will be fitting up with new pistons and would like to change out the all the bushings. Everything I come across is for NA application. I know the OEM turbo pistons have a bigger pin diameter but none of the sites I searched differentiated between the NA and Turbo...
  10. J

    WTB: IDIT Connecting rod

    Anybody out there have a spare IDIT rod they want to part with?
  11. J

    oil leak from timing gear cover

    I have been chasing a fairly good oil leak since I did my rebuild. Couldn't pinpoint it at first, as it was probably coming from multiple places. I was getting oil driipping down the back of the starter and oil pan. Decided to go back in and reseal the top of motor just to cover all bases. The...
  12. J

    Electric fuel.pump install questions

    Hi all! Looking for little help with my Holly Red electric fuel pump install . After have some issues with my Facet pump and reading the most recent thread on the subject I decided to give this pump a go. My biggest issue is how hook up to the fuel selector valve with the new fuel line. Can you...
  13. J

    Loud thumping noise

    Hi all! Need to call on this great pool of knowledge again. Drove my truck down to the store this morning, all was normal. Started it back up after setting for no more than 5 minutes it fired and ran with a loud thumping sound I thought coming from drivers side. It is a deep thump not metallic...
  14. J

    Power steering issue

    Hi all! Having some issues with power steering. Turns like normal to the left, but turning to the right it feels like there is no power assist. Which is kind of sucks trying to maneuver a four door long bed in and out of a parking lot. The truck is a 91 F-350 4wd. The trucks tracks fine down the...
  15. J

    best way to tighten the fan clutch

    I feel like this might be a stupid question,but here goes. Replaced my fan clutch now how the heck do you keep the pulley from turning while tightening that thing down. I have a serp setup with the belt already on. I have tried wedging a piece of wood between the pulleys but no luck. Do I need...

Latest posts

Forum statistics

Threads
91,311
Posts
1,130,171
Members
24,121
Latest member
720Diesel

Members online

Total: 407 (members: 3, guests: 404)

Share this page

Top