Search results

  1. vandy7.3

    If someone's looking for a truck, check this one out...

    Will do
  2. vandy7.3

    If someone's looking for a truck, check this one out...

    I'll ask the guy about the truck and get some details for you
  3. vandy7.3

    If someone's looking for a truck, check this one out...

    It's listed at almost 6 grand. Granted it's fairly nice looking, but that's pretty high on price for the miles that are on it
  4. vandy7.3

    If someone's looking for a truck, check this one out...

    He's coming to my place for the timing. With a different truck. But I can ask him about the truck if there's anything specific you wanna know?
  5. vandy7.3

    If someone's looking for a truck, check this one out...

    The first one posted is owned by a guy on here, I think.. Im timing his other truck next week if it's the same guy.
  6. vandy7.3

    If someone's looking for a truck, check this one out...

    I checked it out, it does look very clean but I gotta have a 4 wheel drive truck
  7. vandy7.3

    If someone's looking for a truck, check this one out...

    Ya I've seen both of the trucks posted in stl. The blue one is nice but still way over priced. And the other is 2wd for sure. Don't really need or want anything but a single cab. I just think it would be sweet to have a dually with a flat bed.... Guess I could always put a dually rear end under...
  8. vandy7.3

    If someone's looking for a truck, check this one out...

    If that red one was a manual I'd be all over that. My truck is pretty well the same thing except manual and a little more beat up, but everything works good on it
  9. vandy7.3

    Lets see your turbo air filters

    Ya same here, I've had no issues getting it apart or back together
  10. vandy7.3

    Lets see your turbo air filters

    There, he beat me to it haha
  11. vandy7.3

    Lets see your turbo air filters

    I have the same filter. Ordered it off amazon. It's a spectra brand inline filter
  12. vandy7.3

    Lets see your turbo air filters

    Oh ya pictures are on the first or second page
  13. vandy7.3

    Lets see your turbo air filters

    http://www.oilburners.net/forums/showthread.php?t=69571 Idk if this will work or not
  14. vandy7.3

    Lets see your turbo air filters

    I'll have to take another picture of mine tomorrow and post it. Got a new phone and haven't transferred pictures yet... But I have an inline filter with the factory snorkel that bolts to the radiator support
  15. vandy7.3

    injectors

    Lots of good info there Gary. Just wanted to point it his name is Justin not Jason over at R&D. Hate for the OP to go looking for the wrong guy haha
  16. vandy7.3

    injectors

    I have my stock pump maxed out on the fuel screw and a set of g codes from r&d. My egts haven't gotten any higher than 1100 degrees, and you gotta push it pretty hard to get them that high.
  17. vandy7.3

    TIME TO MAKE THIS TRUCK LOOK GOOD......

    I did a cheap diy paint job on an old 77 chevy truck I had. Patched up some rust and did some quick body work. Then sanded down everything with 180 and a d/a. Bought van sickle from orshlens. 2 coats of primer sealer let that flash off for about 30 minutes and then 2 good coats of international...
  18. vandy7.3

    rear main seal install

    I just got done replacing my clutch and going to a smf. I replaced the rear main while it was easy to get to. My truck had 81,000 miles on it and I didn't have to use the sleeve for the crank. I also bought my rear main from oriellys, the one I ordered from Ford looked like a POS and didn't want...
  19. vandy7.3

    Gauges

    There you go, I couldn't figure out how to post the link over my phone haha. Thanks ironworker
  20. vandy7.3

    Gauges

    It's in the tech articles,I just looked. The title is called factory gauge replacement. The replaces all his gauges with after market ones and makes them look really nice in the factory dash.
  21. vandy7.3

    Gauges

    The thread is in the tech articles
  22. vandy7.3

    TIMING SERVICE REGISTRY

    State: Missouri City: jefferson city (central mo) Capability: pulse method, all tools necessary. Equipment: kent moore j 33300 bought from icanfixall ready to work. Contact info: shoot me a PM for cell phone number. Cost: free is free, unless you bring beer. I won't turn that down
  23. vandy7.3

    Got a turbo kit, some questions and install thread

    Ya I wrapped all mine before installation. If I had to go back and do it now I'd say to heck with that and roll with what I have. But as for the turbo blanket, you can put one if those on with the turbo on the truck. Might be a little tricky but doable.
  24. vandy7.3

    Got a turbo kit, some questions and install thread

    You don't have to move the clutch line. If you're worried about heat buy a turbo blanket and wrap your pipes, that will keep heat down
  25. vandy7.3

    Frustrated but still trying........

    In the first post he said it's an 89 f350. So I'm assuming it's a 7.3 unless the engine was changed to a 6.9 for some reason.

Latest posts

Forum statistics

Threads
91,305
Posts
1,130,019
Members
24,115
Latest member
Tyler9828

Members online

Total: 553 (members: 2, guests: 551)

Share this page

Top