Search results

  1. Greg5OH

    Factory Intake Manifold

    No issues, $50 plus shipping (approx 25$ IIRC). PM me for quickest response.
  2. Greg5OH

    91 long block and 94 short block $200-MI

    selling all my IDI stuff, 91 is compelte minus IP/injectors and no head bolts, good motorcraft fan clutch 94 is factory turbo short block, no oil cooler also have an FS6 compressor, condenser, some misc stuff i will toss in for a few more $. would liek to sell everythign IDI i have. Located...
  3. Greg5OH

    Custom AC lines?

    Since the cummins conversion, I am still using the stock ford evap and drier. But using dodge compressor and condenser. How can one go about making new lines that fit both ends? Is it possible to use hydraulic lines with welded on AN fittings? No idea about mix and matching ac parts...
  4. Greg5OH

    Sterling carrier setup?

    so im in the process of putting a detroit locker into my 10.5" Just need a quick sanity check.. First time i put it in, tapped the caps a few times, used the stock shims, torqued to 80, i had 25 though backlash. ok, add some to driver side, take equal amount out of passenger side. i tapped the...
  5. Greg5OH

    40222N Facet Dura-Lift Fuel Pump $80

    For sale is a 2 year old facet duralift fuel pump. No issues, just doesnt need my pressure needs with the cummins engine. $80 shipped to your door. This is 33 gph, max 8 psi i believe.
  6. Greg5OH

    94 Turbo Rods

    $185 shipped for 8 94 factory turbo rods.
  7. Greg5OH

    FS6 AC Comp, 1 wire 150amp alt, 6.0 IC, Brackets, IP Lines, HD GP Harness

    All prices are SHIPPED 6.0 PSD Intercooler. $175 shipped. $100 local pickup home made heavy duty harness. 4awg feeding to an 8 awg split feeindng 10 awg stringers. $40 8x 2 month old beru glowplugs $40 1 wire 150 amp alternator using 94-06 mustang case. $90 FS6 AC compressor off a 91 factory...
  8. Greg5OH

    7.3 ARP Head Studs $385 shipped

    Washed, cleaned sprayed down with WD40 ready for a new home. $385 shipped.
  9. Greg5OH

    7.3 Injector lines

    Complete set, $100 shipped to lower 48. Should have the cyl1 adapter, need to double check..
  10. Greg5OH

    7.3 Cylinder heads-core

    $100 located in Ortonville MI. Guides are probably shot. these are for cores only. Pics to come.
  11. Greg5OH

    7.3 ARP Head Studs-1 Pass-$380 shipped

    1 pass on these guys. Was running them in my 7.3 boosting 20+ PSI all day, no issues. Don't necessarily have to pull heads to put these in either. I took out 1 bolt, and replaced with 1 stud at a time. $380 shipped to lower 48. Will get pics soon. they are still installed on the engine...
  12. Greg5OH

    Bricknose maybe OBS gas pedal

    WTB a "gas" pedal for a bricknose. My shaft be all worn out and sloppy!
  13. Greg5OH

    94 factory turbo engine long block parts

    Turbo rods: $240 shipped Front Balancer: $80 shipped Oil cooler: $70 shipped Camshaft: $75 shipped Crankshaft: $75 + shipping ($$ probably) Block: $80 local pick up preferred but will ship if you really want.. Front Cover: $75 shipped Rockers: $50 free shipping Pushrods: $40 free shipping
  14. Greg5OH

    turbo 7.3 R&D parts 2wd ZF5 fresh Luk

    Im selling my entire IDI and ZF5 setup. Located in MI. Shipping is on the buyer. All prices in USD. R&D Stage 1 injectors : 320$ free shipping R&D intake: $200 7.3 Studs: $400: free shipping LuK SMF complete setup: $240 $400 2wd ZF5 SM-42. Does grind 2nd gear if you shift too quick when...
  15. Greg5OH

    Think im done boys...12v time..

    Hopefully I dont get banned for this...but I think im going 12v with nv4500 into P9106... Will be posting me stuff for sale soon enough once the swap starts.. picking up a 96 dually with 270k miles on it for 1800 or less within the next week... Im sure the IDI would wake up with a good pump...
  16. Greg5OH

    wtb: ZD9 glow plug harness

    Looking for a good condition glow plug harness for ZD9 glowplugs. Please PM me price shipped to 48462. thanks.
  17. Greg5OH

    Conestoga pump

    I have seen a few bull moose and 1 omega pump pop up before. looking for a good condition used one if anyone is parting out their truck. thanks.
  18. Greg5OH

    Advance plunger leak on ip...home reseal?

    I have a spare pump id like to try to see if it is infact my IP that is causing my cold start issues as described in the "big oil leak into compressor" thread. It has a small leak past the advance plunger on driver side. Can i replace this seal whithout getting into the rest of the pump and...
  19. Greg5OH

    alternate turbo feed line ports?

    I currently have my turbo being fed off the back of the block..Pretty sure the crushed the brass 1/8 to 1/4 adapter.. im just finding out there is a port by the oil filter on the block I can use to feed the turbo?! If so I am deleting that rear feed right meow. Man should thought of this when my...
  20. Greg5OH

    #1 cylinder IP adapter

    Looking for that 1 adapter for number 1 cylinder by the filter. A friends is all jacked up. PM me if youhave one available, thanks!
  21. Greg5OH

    big oil leak into compressor?

    a perplexing problem recently occurred. Still got the S366 on the engine, no axial play, but started noticing alot of blue smoke while idling. I go to drain my catch can and the thing pours out almost 2 quarts, way over its capacity. Also all my seals started leaking. Ok, so it filled up all the...
  22. Greg5OH

    ZF small shifter rubber boot?

    I tore the little underboot that wraps around the shifter base and can be changed by removing the shifter base from the trans. Anyone have a P/N or know where to buy a new one? Thanks.
  23. Greg5OH

    Fuel filter heater?

    I have long ago deleted my stock fuel filter head heater due to leaks. In its palce i have (i believe) an M12 plug. Wondering If can take that out, or put a recuding adapter in there, and run a little rod heater directly into there? Or can i drill the venry center of it and put something like...
  24. Greg5OH

    burning sheared synthetic oil in IDI?

    I have the opportuninity to get some sheared synthetic oil. DOnt know the viscosity, but this comes from a never fired engine. The engine is just spun by a dyno for 20 hours, so the oil has no soot or contaminants in it. IMO this is the perfect oil to burn, it is synthetic though-should be...
  25. Greg5OH

    gasket/ or ring for lemon timing cover?

    DOes anyone have or knwo the size of the O ring or gasket which goes behind the lemon cover on the timing gear housing? 3rd time tryign to reseal with RTV and still get a bit of blowby past it even after curing overnight. Probably some contaminants left over on the housing that im not able to...

Latest posts

Forum statistics

Threads
91,288
Posts
1,129,816
Members
24,106
Latest member
lewisstevey7

Members online

Total: 784 (members: 11, guests: 773)

Share this page

Top