Recent content by dtrujillo63
-
-
-
FS: 1994 Ford F250 7.3 Turbo Diesel
Too much work to convert to 4wd.- dtrujillo63
- Post #10
- Forum: Marketplace
-
FS: 1994 Ford F250 7.3 Turbo Diesel
It's a 7.3 IDI Turbo and yes, that's my German Shepherd. ;Sweet- dtrujillo63
- Post #7
- Forum: Marketplace
-
FS: 1994 Ford F250 7.3 Turbo Diesel
- dtrujillo63
- Post #2
- Forum: Marketplace
-
FS: 1994 Ford F250 7.3 Turbo Diesel
sold..............- dtrujillo63
- Thread
- Replies: 16
- Forum: Marketplace
-
Where can I buy a wastegate actuator?
I broke the wastegate actuator on my 7.3 idi factory turbo while trying to adjust the boost. Where can I buy a replacement actuator? If you guys have a part number please post it up. Thanks!- dtrujillo63
- Thread
- Replies: 6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
It was my multimeter. After using the multimeter that I borrowed from work, the TPS is now reading 1.1 at idle and 4.4 and full throttle. Since I only use my truck for towing, I might adjust it to 1.2. Gary, the picture I used was one that I found on Google images. My TPS is grey.- dtrujillo63
- Post #18
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
That's exactly how I installed it. One of the allen screws is going through the hole in the throttle shaft, and the other is just tight on the shaft body. While looking at the pump, one screw faces up towards the sky, and the other is facing forward towards the front of the truck. I did have to...- dtrujillo63
- Post #15
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
I just fixed the attachments. Was I not suppose to remove the PIN that the arrow is pointing too? I couldn't get the round lever with the allen screws to go on without removing the PIN.- dtrujillo63
- Post #13
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
Here are some pictures that show the pin that I was referring too. I had to remove it to install the round lever with the allen screws. Did I do that right?- dtrujillo63
- Post #11
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
Forgot to mention, the top wire had 9v at idle and the bottom wire had a constant 5v no matter what. Not sure if that's normal.- dtrujillo63
- Post #10
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
No matter what I do, I can't seem to adjust the tps so that it has an idle voltage of anything below 2. It either has no idle voltage or 2 if I turn the tps completely towards the front of the truck. Maybe I installed the tps and it's bracket wrong when I switched it from the old pump to the new...- dtrujillo63
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
Hey Gary, I decided to knock it out yesterday with the help of my brother. I torqued down the injectors to 33lbs (per Mel's article). I was wondering about the TPS since I have an automatic. I tried bolting it on in the exact same position it was on originally. What's the process to correctly...- dtrujillo63
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Moose Pump Install
I just got done installing the famous Moose Pump (Junior) and a new set of BB injectors. I have a couple of questions regarding my install, can you guys take a look at the attached diagram and approve or disapprove on how I connected my return line kit? Since I have a 7.3 IDI Factory Turbo, it...- dtrujillo63
- Thread
- Replies: 17
- Forum: 6.9L IH & 7.3L IDI Diesels
