Regulator has not been rebuilt to my knowledge, and which screen?? I have ordered a new pump and hoses since it has been suggested these tend to leak out the weep hole. the last one has only been on there a few years but I have been smelling fuel for a while now and the valley pan is covered in...
Well I have been smelling fuel for a few days before this happened but could not find a leak and my rear tank has had just 4 gallons in it for 5 years and is capped but the fuel gauge still reads about 1/8 tank. Do not know how I can check fuel pressure at the filter housing the nipple on the...
I have a 97 ford 7.3 duL tanks problem. A couple of weeks ago my 97 appeared to run out of fuel. Since them I have added 7 gallons diesel into front tank. Fuel selector switch appears to be working. Filter cover off and cranking appears to be getting fuel / air but wont fill the filter housing...
I am trying to put an electric fuel pump on my 97 psd 7.3, crawled under it to have a look at the lines coming out of the selector valve. Someone stated the feed is 3/8 and the return is 5/16, however my lines are 5/16 on both feed and return from the electric selector valve up to the manual...
This last weekend my 91 F250, 7.3 ran out of fuel while parked on side to side incline, Showed 1/4 tank, but I assumed it uncovered the pickup line. Put in 5 gallons and got it started after filling filter and a little ether. Started and let it idle for about 15 minutes. While running it began...
I have been searching high and low for the nut inside the output yoke of a ZF-5 in 97 F250 with 7.3 powerstroke.
I have ordered and paid for over 10 online in the last 3 months only to be informed they are obsolete and get a refund.
No one can even tell me the thread size and pitch.
Anyone with...
I did mine in my previous truck but I removed mine, stripped everything off of it and fiberglassed mine with fiberlass mat, 4 layers on the underside and 2 on top. lot of work but it did come out pretty good for me. the other advantage to the fiberglass was being able to imbed a piece of 1/4...
I need the yoke that goes on the rear of the trans. already replaced the ujoints not more than a year ago. But i will try to get in touch with them about the yoke, never thought a yoke for a zf 5 would be so hard to find.
In a big bind, got a bad vibration at 70 mph the other day. Limped it home and found the nut is gone off the tail shaft of my trans and the little ******* that hold the u-joint end caps in the yoke are worn down to the point i can move the joint in the caps 1/8" because the ******* are almost...
went out and replaced the cps sensor and went to check the ebp valve the sensor is in place but there is no plug running to it. looked around and cant locate a plug anywhere on the harness that might plug into it. i checked wiring diagrams but couldnt locate it physically. if someone can look at...
i know, i think thats the cps those are what showed up from forscan. will be trying to get to most of it this weekend now that we have sunshine.
When i had the forscan hooked up i ran it around and all over the place trying to get it to cut off but it didnt
THANK YOU got the forscan and got it working, got 3 codes, 2 for exhaust back pressure. I think i will have to bypass 1 since it is open 4" exhaust, I reset pcm back to factory and it already runs better, still have to replace the CPS because it still shuts off sometimes, been raining here for a...
went and ordered a forscal tool,
FORScan OBD2 Adapter, VINT-TT55502 ELMconfig ELM327 modified For all Windows
now all the files i have to download for it to run come back as infected malware. and incompatable with windows 10. Totally useless. I am trying to send it back and order a different...
ipr and ICP were both replaced 2 years ago. this has been doing this for longer than that, just not as often as it is now. and yes both were motorcraft
97 7.3 shutting off while driving, while sitting in traffic etc. I dont understand this i have read every possible thread. my truck will be running fine then it just shuts off at different times, sometimes it will refire if i am moving but if it shuts while at a stop i can usually just turn the...
the valve cover gasket has 2 plugs on it. the outer harness plugs into the gasket and it passes thru to the harness underneath the valve cover.
quote from member Greenskeeper;
You can pull the valve covers and confirm that all injectors are flowing the same amount of oil from the oil spouts. If...
i have had the same problem for over a year. a suggestion was made by another member to check walve cover gasket wiring and harness going to injectors and glow plugs.
yes the scan tool was hooked up trying to read live data that is why it would come and go every few seconds. put the scan tool away. it then was back the way it was. never occured to me scan tool would do that.
the miss does not go away at all at idle warm or cold. I dont know about anything...
Mine is a Bosch unit. But made some calls and found out that this engine and factory ECU cant be scanned with a regular OBD II scanner while running. It will only allow read and resetting of codes in key on engine off.
Now I know. Either way i have a "miss" only at idle and thought i could see...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.