Search results
-
Dana 50 wheel bearing replacement, how in-depth should I get
Big order came in, all new wheel bearings, seals, and ball joints. I went with Mevotech supremes, but I think I might return them and go with XRF brand, read a lot of good reviews on the XRF ones, vs many mixed on mevotech and moog. Plus I already have XRF uppers.- HS108
- Post #16
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Dana 50 wheel bearing replacement, how in-depth should I get
Im gonna check the u joints, I dont use 4wd much, and if I put on 1.5-2k miles a year thats a lot. If I was gonna swap axles, I put in a new 08+ super duty coil spring ones I have to draw the line somewhere. Ill wait on the leaf springs, those can be done without undoing what I already have...- HS108
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Front Hub - 1991 F350 4x2 Dually - How To Tell If Wheel Bearings Are Bad?
Going by videos ive been watching, you want to tighten the inner nut to 50 ft/lbs while rotating the hub, then back off 1/4 turn so you can line up the nut retainer ring, then you tighten the outter ring (jamb nut) to 150+ ft/lbs of torque...- HS108
- Post #6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Dana 50 wheel bearing replacement, how in-depth should I get
Update: Needle bearings and ball joints ordered, also going to be inspecting and probably replacing the pivot bushing as well I need to send out my PSOM to be rebuilt anyways, so truck is down for awhile- HS108
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Dana 50 wheel bearing replacement, how in-depth should I get
you sir, are not helping lol- HS108
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Dana 50 wheel bearing replacement, how in-depth should I get
What started off as a simple brake job has turned into a full blown rebuild. I wanted to "just" replace the Pads, rotors, hoses, and calipers on my TTB dana 50, but it has turned into a whole production... Now im replacing the bearings and seals and repacking it all with fresh Red N Tacky (I...- HS108
- Thread
- Replies: 65
- Forum: 6.9L IH & 7.3L IDI Diesels
-
1993 7.3IDI Turbo vs 1994 7.3 IDI Turbo
if you already have a turbo IDI, why are you looking to get a new "brand" turbo set up, and not just upgrade the ATS turbo setup you have? the 93 and early 94 year model trucks are the only ones that came with the ATS turbo set ups installed from ford, some dealers would install turbos and sell...- HS108
- Post #14
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Glow Plug Wire Connector Replacement
Maybe, I have a new glow plug harness sitting on the shelf from ididiesel.com and thats how the bullet connectors are done, but it does look like a thick rubber heat shrink, not the hardware store special kind. Ill try to post a picture but idk how anymore because i would always upload from...- HS108
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Oil overfill ok?
I always just add 12 Qts with a powerstroke filter, what am i gonna do with 1 qt extra when I buy 3 gallons of oil... come on...- HS108
- Post #29
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Random surging while driving
No worries man, Fixing the truck got me back into it, so im back on the forum for a little bit, till I fall off again lol- HS108
- Post #27
- Forum: 6.9L IH & 7.3L IDI Diesels
-
losing my mind o/d light flashing
you can scan the codes with this reader...- HS108
- Post #10
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Random surging while driving
I have a new hard line replacement kit from the lift pump to filter head if you want, Im in CT too. I just replaced my lift pump because it was leaking fuel. I had the hard line delete kicking around the house for a long time, bought it from mike green i think back in the day, but i didnt use...- HS108
- Post #23
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Batteries
I had the advance auto Golds, lasted me 10+ years, but I just replaced them with "seconds" batterys from a local battery shop. 150 for both out the door- HS108
- Post #49
- Forum: 6.9L IH & 7.3L IDI Diesels
-
-
Zd29s vs Zd9s...for the inquiring mind...
Just ordered 8 zd9s from Amazon, and it was true zd9s not zd29- HS108
- Post #59
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Zd29s vs Zd9s...for the inquiring mind...
Where does the controller get its “info” if the engine is hot or not?- HS108
- Post #58
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Zd29s vs Zd9s...for the inquiring mind...
Can you still order NOS zd9s?- HS108
- Post #54
- Forum: 6.9L IH & 7.3L IDI Diesels
-
AC thread - orifice tubes
hahaha, it took me a few posts to say " man ive read this before" Then I looked at the date, and laughed and said oh ya I have read this before when I was working on my AC, then I saw a new post 12 years later, and the posters very first post on this forum is bringing an old thread back from...- HS108
- Post #25
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Ye olde ATF in the Fuel Filter
I also just run full atf with a filter change, easier to pour in than diesel.- HS108
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
New IP, GP, and injectors… she’s running but smoking like crazy got a lope too
First and formost, Welcome. Secondly, I know money is tight, but you can end up costing yourself so much more in the long run with those cheap glow plugs. The Buru Motorcraft ones are the best and honestly cheap enough. Lastly, After sitting that long, gonna have to burn off a lot of stuff...- HS108
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Glow plug troubles
I think you need a new wiring harness for the glow plugs, Even tho it may look good, the wires inside can be shot, that’s a lot of heat they take on top of the motor like that. From your list of everything you have replaced I don’t see a wire kit on there, yes you may have the 12v and the...- HS108
- Post #10
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Kent Moore J33300 timing kit questions
Well, update 2... I saw a full Kent Moore meter pop up on eBay, I couldn’t resist. Offered 150 and he took it. So now I have 2, I will make one complete set, and resell the other. Or add it to my parts pile lol Sent from my iPhone using Tapatalk- HS108
- Post #14
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Kent Moore J33300 timing kit questions
I was able to get my hands on a inductive timing light, for a good price... free So I will test it out, report back with pictures. It’s not gonna be tomorrow or the next day, but it will be one day lol Sent from my iPhone using Tapatalk- HS108
- Post #12
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Kent Moore J33300 timing kit questions
Something like this for an advance timing light? Actron CP7528 Advance Timing Light, Gray https://smile.amazon.com/dp/B000BSWEHS/ref=cm_sw_r_cp_api_glt_fabc_85MYEJ73RXKEWGV8YXKX There is one of these for sale locally, I can pick up cheap just to try it. Sent from my iPhone using Tapatalk- HS108
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Kent Moore J33300 timing kit questions
Yes, but a new probe from Kent Moore is 400. Sent from my iPhone using Tapatalk- HS108
- Post #8
- Forum: 6.9L IH & 7.3L IDI Diesels
