Search results

  1. tbowker

    6.9 E350 camper down in Cranbrook, BC

    Huh, figures. I sent my reply after only reading the first few entries of the thread and not only am I late, but now I find out the party is over. I'm glad you got the issue figured out. :thumbsup:
  2. tbowker

    6.9 E350 camper down in Cranbrook, BC

    I know I'm late to the party, but this is the fuel selector valve I currently am using. It has close to 15k miles on it with no issues.... so far.
  3. tbowker

    So what did you do with your truck today?

    I replaced both door hinges and the door striker pin on the driver side. Next time, if I have to replace the hinges on the passenger side, I will remove the fender to make the job easier. I must have put the door on and off about six times before I got the gap correct.
  4. tbowker

    parallel turbos

    Yeah, cut him some slack.... just because the pavement was poured by the ancient Roman's doesn't make it any less of a road. Funny though, that @Nero was the first one to comment on it. :rotflmao
  5. tbowker

    So what did you do with your truck today?

    This one I don't remember. I have a couple of motorcycles without turn signals so I have to use hand signals on those. Most people drive like they're running time trials for Nascar so even if they understand what you're signaling, I don't think they care.
  6. tbowker

    the 1942 pontiac

    Wow, I wish you lived closer... I'd hang out and pick your brain. Well, if you would tolerate me. Impressive!!!
  7. tbowker

    Cup holders

    It appears to be Homer Simpson approved, he apparently finished off the donuts first.
  8. tbowker

    Cup holders

    Hmm, valid point... well put. Arrgh, why must you torment me so?! And then the salve to make it all better. Sigh, this has been like an emotional roller coaster....I need a nap.
  9. tbowker

    Cup holders

    Hmm, but you do get covered with grease and oil... they're like washable tattoos. For some reason I thought it was @Jesus Freak who started this thread, ugh. Just because I'm wrong, it won't stop me from firing off wise cracks full tilt, wide open and out of control. :bail
  10. tbowker

    Cup holders

    Peter Steele was something like 6 foot 12, I'm thinking our Nero is a bit more vertically challenged. I could be wrong, after all, I only saw that nightmare inducing eyeball shot.
  11. tbowker

    Cup holders

    WHAT?! Simply because you're the cupholder thread originator doesn't mean you can go all cancel culture and become a thread tyrant. Sheesh, and he talks about @Nero being a rotten no good nick. -Flame Thr Hello pot, yeah, this is the kettle. ;Poke
  12. tbowker

    So what did you do with your truck today?

    I'm thinking with that sense of humor, he's not the only one who's mom had him standing in the corner. Are you paying attention to this @ttman4 :rotflmao
  13. tbowker

    So what did you do with your truck today?

    Selective editing at its finest!!! :hail
  14. tbowker

    So what did you do with your truck today?

    What is this.... multi millennium treachery?! One Nero watching out for the other one. ;Really
  15. tbowker

    So what did you do with your truck today?

    That ought to put a smile on Greta Thunberg's face.
  16. tbowker

    So what did you do with your truck today?

    Just goes to show how history repeats itself.... not only was Rome not built in a day, but neither is that engine.
  17. tbowker

    So what did you do with your truck today?

    Yikes!!! Judging by the maniacal look in that eye, I'm certain that poor engine knows better than to tempt wrath and simply huddles under its blanket, quivering in fear. :rotflmao
  18. tbowker

    Wiring harness and thinking about selling

    My grandfather and a couple of uncles had a cattle ranch in Opal, South Dakota. A cousin is still there.
  19. tbowker

    So what did you do with your truck today?

    These beads are far more common than I ever imagined...I am so out of the loop. I looked them up on Amazon, cheap enough to give a try. See, this is how I got started on this bead topic to begin with. The evil death wobble. :rotflmao This is something I'm considering also, although I usually...
  20. tbowker

    So what did you do with your truck today?

    Huh, now I'm intrigued. Much cheaper than buying a static balancer. Thanks.
  21. tbowker

    So what did you do with your truck today?

    I've never heard of these, what are they?
  22. tbowker

    Traveller Smurf (Cubey's '89 van)

    So then what is the maximum efficient temperature?
  23. tbowker

    So what did you do with your truck today?

    A couple of weeks ago I got a front end wobble at around 50mph. If I went slower it would stop and faster it would also stop. I haven't driven it much since then since I was repairing other stuff on it first. So today, I took it to get the front wheels balanced. After sitting for an hour and a...
  24. tbowker

    Traveller Smurf (Cubey's '89 van)

    That's good to hear, because that's what mine runs.
  25. tbowker

    Could you Sleeve down an old crusty 7.3 to run 6.9 pistons???

    I knew several guys who ran the dual plug heads, I never went that route. That 84" kit makes a huge difference. I've never minded a 4 speed but that road king with the 5 speed is nice for traveling. You've had your shovel for a couple of years longer than I've had my 53 pan, I like your style...

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,944
Members
26,577
Latest member
Jrlew87

Members online

Total: 1,428 (members: 8, guests: 1,420)

Share this page

Top