Search results

  1. kbenz

    Stack

    @Jesus Freak lol. Wish I had something to bend pipe that big. I can do 1.250 pipe and 1.5” square. I’m working on a deal on a steady supply of hydraulic fluid
  2. kbenz

    Stack

    @Jesus Freak yea yea yea .lol I’m running a rebuilt pump and injectors. It’s running great. Just smokes under heavy acceleration
  3. kbenz

    Stack

    I don’t carry much payload. That stack will be beside my fuel tank
  4. kbenz

    Stack

    Never said a muffler had anything to do with smoke.
  5. kbenz

    Stack

    I forgot to mention I burn wmo. Pump hasn’t been turned up
  6. kbenz

    Stack

    I’d rather keep mine through the bed. I have enough room for what you’re saying but I’d like to get it a bit further from the cab
  7. kbenz

    Stack

    I know it’s frowned upon by most but when I hit a hill pulling anything or just getting on it getting up to speed it smokes pretty bad. I really don’t like it. It seems kinda obnoxious at times. It’s a crew cab so I do have room for a muffler. I built this stack out of 3x3x3/16” tube. Questions...
  8. kbenz

    So what did you do with your truck today?

    Wasn’t today but I installed new headlight housings and upgraded to leds
  9. kbenz

    Battery Cable Routing...

    Both my positive posts are on the inside
  10. kbenz

    2025 i.p. builder discussion

    $500? run away
  11. kbenz

    Rug source

    Talked to him today. I can come any morning. He said he’d be happy to swap totes. Shouldn’t take long for the water to separate should it?
  12. kbenz

    2025 i.p. builder discussion

    performance diesel of Albemarle rebuilt mine. Been good so far. was recommended by several locals
  13. kbenz

    Rug source

    not sure yet. I'm hoping we can just swap totes. I've only pumped oil so I'm not sure if I could tell the difference between gas and water
  14. kbenz

    Before I buy injection pump....

    Had mine rebuilt local from a standyne approved rebuilder. If you want to do an online guy I'd only use r&d,moose or cdd. If someone says they can do it for $500 run
  15. kbenz

    Thinking of making a reusable oil filter from stainless steel sanitary pipe, fishing for your thoughts.

    I remember hearing a story about a guy that developed a carb that would get 70mpg. They bought him out and it all disappeared. don't know if its true or not
  16. kbenz

    Rug source

    I haven't gotten any yet so not real sure. He told me it would definitely have water and trash mixed in it. I have an old oil 350 gallon oil drum that I welded some legs on. got the fittings ordered for it. Gonna use it to settle it out. shouldn't take long for it to separate I wouldn't think.
  17. kbenz

    Rug source

    Found a source for some rug but has trash and water in it. Should I just settle it out? Or mix with oil before I run it through the centrifuge? Or both?
  18. kbenz

    WANT TO TRY A LIL BUDDY HEATER TO WARM ENGINE

    they are propane heaters
  19. kbenz

    Electrical issue

    Haven't had any issues since I put a kill switch on the wires that got to the fuse block. The draw might have wobbled .01amp when I was testing
  20. kbenz

    Electrical issue

    Already went through the fuses with no change. I put a kill switch on it for now. Which usually means it’ll stay that way
  21. kbenz

    Electrical issue

    yea. One goes to inside fuseblock and one for the fuseblock under the hood I would think. Just don't know where to look for that draw?
  22. kbenz

    Electrical issue

    No. I found that one. This one goes in the harness around the front of the truck. In front of the batteries and radiator
  23. kbenz

    So what did you do with your truck today?

    New headlight housings, relays and led bulbs. Found out the housing mount clips aren’t too bad if you just pull the piece they’re mounted to
  24. kbenz

    Electrical issue

    This rough looking wire set is attached to the hot side of the starter relay. I have a 5.6amp parasitic draw on them wires. I’m guessing they feed the fuseblocks. I pulled all the fuses with no change in draw. Any ideas things to check? Just started doing this
  25. kbenz

    87-91 F Series Headlight Connector Replacement and Relay Mod

    Same

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,941
Members
26,574
Latest member
abcdefg

Members online

Total: 1,767 (members: 3, guests: 1,764)

Share this page

Top