Search results

  1. 79jasper

    Question re: fuel filter light

    Just my opinion, but sounds like you have a restriction.... Sent from my SM-N960U using Tapatalk
  2. 79jasper

    Dana 50 front locking hub bolts

    Hardware store. Sent from my SM-N960U using Tapatalk
  3. 79jasper

    Zf5 synchros

    Nothing to really "flush." Dump the old, put new in. Sent from my SM-N960U using Tapatalk
  4. 79jasper

    Power Burst

    More likely icp sensor. CPS would cause a stall. Sent from my SM-N960U using Tapatalk
  5. 79jasper

    Glow Plug Leak

    That is correct. You would never have a need for that, if everything else is clean and torqued properly. Sent from my SM-N960U using Tapatalk
  6. 79jasper

    Questions about Dana 70 wheel seals

    I forget you are "on the move." Sent from my SM-N960U using Tapatalk
  7. 79jasper

    Hydraulic Winch setup info needed.

    Make sure the pump meets the specs of whatever winch you go with. And I don't mean bare minimum. Ideally you want to meet the winch specs at or near idle. Filter needs to be in the return. I would go ahead and run some lines to the rear of the truck. Or even the front of the bed. Also, iirc...
  8. 79jasper

    Questions about Dana 70 wheel seals

    These are handy. https://www.harborfreight.com/automotive/jacks-jack-stands/floor-jacks/22-ton-airhydraulic-floor-jack-63273.html Use them on dump trucks. Sent from my SM-N960U using Tapatalk
  9. 79jasper

    Questions about Dana 70 wheel seals

    Have a harbor freight nearby? Sent from my SM-N960U using Tapatalk
  10. 79jasper

    Pitman arm suggestions.

    This is where the pickle fork attachment for a air hammer comes in handy. I watched a guy beat on one for a hour before. Wouldn't budge. Then took it to a shop, guy barely even tapped it with the air hammer. Lol Sent from my SM-N960U using Tapatalk
  11. 79jasper

    Air-water CAC/intercooler on an IDI?

    Plenty of people putting CAC's in obs powerstrokes. They 94 still ran the idi style wide radiator. 95 went to a different setup, but identical size radiator. Sent from my SM-N960U using Tapatalk
  12. 79jasper

    High oil pressure

    Stuck regulator. Sent from my SM-N960U using Tapatalk
  13. 79jasper

    DO NOT USE STP S3766 oil filters from AutoZone - warning!

    I had a stp once. It was hard turning all the way on. Rather one feels tight or not, I try to look at the contact area. Sent from my SM-N960U using Tapatalk
  14. 79jasper

    Well well well

    Currently sitting at 14.6. Planning to run e85 like we did in the 11. Sent from my SM-N960U using Tapatalk
  15. 79jasper

    So....

    On the LX platforms, they come out the top pretty easy. You could also drop in out the bottom with the engine cradle. Sent from my SM-N960U using Tapatalk
  16. 79jasper

    So....

    Greene racing 210/218 cam, locators, shims, lightweight retainers, hardened pushrods, .625 lift springs, and hellcat lifters to soon be installed.... Sent from my SM-N960U using Tapatalk
  17. 79jasper

    Well well well

    CumminGs is gone, trans was going out 2 or 3 weeks into having it. The 300c went to being the daily. Then went to being my wifes daily. Now she has this. Feels great not having any car payments. 04 Z71. Sent from my SM-N960U using Tapatalk
  18. 79jasper

    Thoughts on this repair?

    Probably not "the best," definitely not the worst. Sent from my SM-N960U using Tapatalk
  19. 79jasper

    Brake troubles

    I usually went to a slight drag. I like tighter than most. Sent from my SM-N960U using Tapatalk
  20. 79jasper

    Truck wont start after clutch job, need help on where to start

    Cycle it by hand. Some have luck by pumping the pedal with it running. The vibration seems to help. Sent from my SM-N960U using Tapatalk
  21. 79jasper

    Brake troubles

    Did you bleed the rabs valve? Just for giggles, check the rear brake adjustment. Sent from my SM-N960U using Tapatalk
  22. 79jasper

    Truck wont start after clutch job, need help on where to start

    What you are holding is a nylon/plastic line that goes to a boost gauge. It melted to the relay. Definitely not a wire. Sent from my SM-N960U using Tapatalk
  23. 79jasper

    ICP sensor changeout......

    Some vehicles take 50 key cycles. Sent from my SM-N960U using Tapatalk
  24. 79jasper

    ICP sensor changeout......

    Typically when a problem is fixed, the light will go away. Sent from my SM-N960U using Tapatalk
  25. 79jasper

    fuel stem check valve....remove that junk!

    I just don't remember seeing one of the few I've pulled out. Probably something else for the deadhead design. Lol Sent from my SM-N960U using Tapatalk
View older results

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,105
Members
26,430
Latest member
Brownlee5212

Members online

Total: 790 (members: 3, guests: 787)

Share this page

Top