Search results

  1. Mt_Man

    Finding the limits of my centrifuge and the sweet spot

    If they are in series the heat will go through to #2 but you will see some drop from 1 to 2. But my setup with and inline heater was still able to warm the tote after going through two fuges.
  2. Mt_Man

    Finding the limits of my centrifuge and the sweet spot

    Pass 5. 3.49oz This stuff is thinned and been settled for a while. Suck off the top and then combine the bottoms of several and dispose of has been my method. Yes heat always helps. Trying to not do heat at the moment. Looks like I am flowing 5oz per min~2.3gph 8oz per min ~3.75gph(I read...
  3. Mt_Man

    Finding the limits of my centrifuge and the sweet spot

    Here is the results of the 4th pass. Sludge is consistent with the other passes, in consistency, maybe slightly stiffer(holds form better). Each pass seems to have less water. 4th pass was 5.86oz. So still less then pass 3, but not by much. Entering the realm of diminishing returns. Setting...
  4. Mt_Man

    Finding the limits of my centrifuge and the sweet spot

    3rd pass done. Well took 54hr to pass 300g through the fuges. So about 5.5gph. Numbers are in. I zeroed the scale for each container type. Left to right pass 1, 2 ,3. Weights 52.83oz, 13.20oz, 7.48oz. So it is interesting that it is now halving the sludge amount. Would be an interesting...
  5. Mt_Man

    Finding the limits of my centrifuge and the sweet spot

    Thought experiment. If I decrease the flow rate even more. Would it be better then currently doing at least two runs. Example. It takes 48 hours to run 300g through one pass. Two passes would be 8day three would 12day. But would see if there was anything getting through. Slow it down (to half...
  6. Mt_Man

    Finding the limits of my centrifuge and the sweet spot

    Been running green fuge (absolute centrifuge) then wvo designs fuge in series for a while now. Got my new pabiodiesel ultimate force centrifuge(UFC)and running it solo. Works great and easy to clean. Finally got around to building a new rack to put all three in series. Pabiodiesel UFC then...
  7. Mt_Man

    Centrifuge bowl design ideas?

    Yah another friend suggested a propane tank. Which I like both his and yours. Right now I think I want to keep it intact. Good idea about a tire balancer.
  8. Mt_Man

    Centrifuge bowl design ideas?

    Let's hear some bowl ideas! So I picked up this chip spinning centrifuge for cheap. It is designed to wring machining chips. I don't think modify the existing bowl would be as good as build a new oil bowl. Also allow me to resell if not adequate for oil cleaning. It has got a decent diameter...
  9. Mt_Man

    PA Biodiesel Supply

    What kind of trouble? Binds up and can't get it to rotate? Mine got hard to rotate with some clay like sludge it got out of one batch. I accidentally left the bowl lid screws loose, didn't double check, and the the gasket squeezed itself out. Needless to say I didn't need to clean the bowl and...
  10. Mt_Man

    PA Biodiesel Supply

    C-shape is like WVO designs and absolute centrifuge (no longer around). Not sure what they are officially called. The cross section looks like a "c" in shape. Simple to build and strong. Pretty easy to clean too.
  11. Mt_Man

    Biobor JF to wmo blends

    Bottom of an wmo/blend tote. Settled long time.
  12. Mt_Man

    Biobor JF to wmo blends

    Has anyone added Biobor JF to their wmo blends to kill microbes for storage? Results? Technically support said it can be used with any hydrocarbons. Gave some other interesting information. Should blend fine and be just as effective, but viscosity might make not mix as quickly so agitation is...
  13. Mt_Man

    PA Biodiesel Supply

    I just got my new fuge, pabiodiesel ultimate force centrifuge up and running. Man I thought removing the bowl lid screws to clean the bowl would be a hassle, but I am a convert. So easy to clean when it's filled up with sludge. Even it's hard like clay or sloppy soft stuff. So much easier then...
  14. Mt_Man

    frick #3 ammonia compressor oil

    It will attack brass and causes black pipe to rust. Great for wmo furnace. Got a buddy that uses it exclusively. Low ash and very clean usually. It can absorb and hold water. I got some yearsss ago. Didn't know what to do with it and after research seemed like it should work and fuges it and put...
  15. Mt_Man

    WMO running in HEUI truck

    Around 1996 international used the p7100 ppump injection pump in the dt466 before going to dt466e. So it would be very close to a ppump 12 valve. Several friends think that it would be an oil eater.
  16. Mt_Man

    WMO running in HEUI truck

    I heard from one guy running it in c12. His experience was diesel and light wmo concentration. He said didn't notice till about 50 percent wmo. Then it cranked a long time to start and smoked. He used it to dispose of wmo and experiment more than savings. Not sure of how long/far he did it or...
  17. Mt_Man

    recommenred 12 v auxilary fuel pump for waste motor oil

    My thought is that the epump might get over worked with viscose fluids and overheat. Is this a concern? Or are they over sized and do just fine?
  18. Mt_Man

    Waste Transformer Oil

    152c flashpoint. Seems like nice stuff pretty low viscosity too
  19. Mt_Man

    Aviation oils?? For wmo fuel

    Did some talking and I just picked up some aircraft piston oil. Looked up the ads and it has a higher autoignition temp then 15w40 oil. In the past I blended it with gas and had decent results. Smoky mainly. This batch I might try it with just diesel blending an see if it's better. A buddy had...
  20. Mt_Man

    WMO and diesel mix in 6.0 PSD

    @miles1400 can you find a 12v or old Ford with a 6.9/7.2idi/7.3ps around you to use that oil in and cut your wmo teeth on?
  21. Mt_Man

    PPump Timing Bump

    This guy has some interesting wmo vids too
  22. Mt_Man

    Oil burning heaters

    Any updates?
  23. Mt_Man

    Waste Transformer Oil

    @Kiwif150 do you know what kind of transformer oil you get?
  24. Mt_Man

    recommenred 12 v auxilary fuel pump for waste motor oil

    I run the stock mechanical lift pump on my dodge 12v's but not the same. I have been running hep-02a on my centrifuge. Running constantly for a few months now. Seems to pump wmo blends okay. Not sure about 100 percent yet.
  25. Mt_Man

    WMO and diesel mix in 6.0 PSD

    There are more people trying it and build info and data. So hopefully they will be posting more about it

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,103
Members
26,430
Latest member
Brownlee5212

Members online

Total: 1,027 (members: 7, guests: 1,020)

Share this page

Top