Recent content by howards@howard

  1. H

    Throwout bearing failed

    The throwout bearing on my new SB clutch failed after 16000 miles I took it out and it was in pieces. The part number on the bearing is F557606 I did my research and its a BCA made in China. The net is covered with articles RE this exact bearing failure I am installing a new Valair kit and it...
  2. H

    Glove box high tide

    It was not a laughing matter I got pulled over by the truck team I tried to hand my registration to the DOT cop it looked like cream chipped beef. The rain water is coming from the roof area it's amazing that it can make it into the glove box. My glass guy wants me to take our windshield and...
  3. H

    Glove box high tide

    2000 F350 Last week I got stopped buy the DOT when I went to pull my registration out of the glove box I found a foot of water in the glovebox. I have no visable leaks at top of windshield, I looked under windshield gasket found a small touch of surface rust. If is is the winshiel seal hows it...
  4. H

    Sticky ignition switch

    sticky key I just did mine the rack and pinion that the key turns is telling you it's about to break. Go to stolen and Recovered web site for parts and instructions on how to rebuild it.
  5. H

    ABS Light On E-Brake Off

    abs E brake switch is on the pedal Assembly on mine. Tiny Little switch that the pedal hits. Yes ABS sensor is on top of rear differential
  6. H

    up pipe donuts

    up pipes Thats a big pain I have done it. I bit the bullet and took the tranny and turbo out. Those bolts are all stuck and the babys bottom is probably cracked. Do a banks power elbo all new pipes. In the long run you will be happy
  7. H

    ABS Light On E-Brake Off

    ABS very common ABS light cause is rear axel speed sensor. Also take your E brake switch out and clean it or replace it. they get dirty
  8. H

    stalls hot

    supply problem Yes the LP runs off a switch on the dash installed by me. thanks If you crip the return line the truck stalls. do you think someone hooked up the two lines backwards
  9. H

    stalls hot

    supply problem There is plenty of fuel at the lift pump shooting out. Pump is running fine. with a gauge on the drain 0psi with truck running and 10 PSI with the truck shut off. So A all the fuel is getting sent back to the tank VIA the return OR B there is a restriction in the supply...
  10. H

    stalls hot

    supply problem Yes my gauge is tapped off the drain. If the gauge is reading zero then I guess it's doing its job for now. So I should disconnect the LP and blow back the line from the filter housing?? Have you ever had relief valve problems and how is that to service?? were is it?? Thanks
  11. H

    stalls hot

    Well we are on week two. I put a permanent fuel gage on it. this is helping with diagnosis. I put the delco EP-158 10psi lift pump on this helped and dropped the tank and cleaned it. it ran great for a week perfect 8-10 psi I thought we were done. It died yesterday no fuel pressure at the drain...
  12. H

    stalls hot

    1994 6.5l 3500 auto 150k random hot stalls, fires dies, let cool over night runs fine for first hour. this week, new lift pump + lines, Wired LP independent w/ relay on key, new FSD and tested suction line for obstructions, new FF. Fuel pressure at the Tee is 4psi at idle, I would think it...
  13. H

    EBP Valve

    EBP Take it out and put in Banks power Elbo.
  14. H

    Can I pull my oil pan without pulling me engine?

    Oil pan Supposably there is a guy up here that will do oil pans for $1400. plus parts he must have it down to a sience. Thats not going to help you though. There is a vidio on you tube on how to lift the cab .
  15. H

    Rebuil

    i am looking for a reputable shop to do a compleate stock rebuild in the Northeast. I want some place that has experiance doing powerstrokes.
See more

Latest posts

Forum statistics

Threads
91,328
Posts
1,130,442
Members
24,133
Latest member
Nanohawk

Members online

Total: 792 (members: 7, guests: 785)

Share this page

Top