Search results

  1. goldsjos18

    Injector nozzles

    Ok guys I just bought a 99 Dodge Ram 3500 with a 53 block no I know this block is prone to cracking. So when my block cracks I was thinking about taking a 6.7 short block and swapping the head and timing cover to make “ 6.7 vp44 “ but I was told the injector nozzles were different so my...
  2. goldsjos18

    blown front diff

    so im hearing a bunch of clunking and grinding from up front so i know i have some issues up their my next question can i pull that third member type pumpkin and pull the shafts and pop the u joints out of the far out side and put the out side splined shaft back in to keep dust out the lock outs...
  3. goldsjos18

    High oil pressure

    is it normal for oil pressure to get this high on the gauge?
  4. goldsjos18

    low boost numbers

    so im running around tearing my hair out with this engine.. just the other week i was pushing the truck and hooning around and i was able to reach 28 pounds of boost. now this week i put my foot to the floor to pass a car and all my gauge read was 7-8 pounds i checked the rubber ring in between...
  5. goldsjos18

    Vibration in the rear

    My 1995 f250 has a slight vibration in the rear of the truck I’m confused as to it could be carrier bearing spins freely I’m supper confused? Any ideas
  6. goldsjos18

    Jockey tank to fuel tank plumbing

    All right so I have a 100 gallon fuel tank that is going to be bolted to the bed of my truck so my next question is how would you guys route the plumbing into the tank of the truck ..... I have no selector valve
  7. goldsjos18

    diffrence between abs unit hubs and non abs hubs????

    is their any size difference in the hub its self can i put non abs hubs in an axle that had abs????? axle is going into a truck that doesn't have front abs and im looking to tidy up the axle as much as possible... fewer wires and such just dont want to spend 250 dollars and it be a bad part
  8. goldsjos18

    6.9 idi engine parts to good home

    i have a lot of left over engine parts from when i swamped my engine in my truck let me know what you all want you just need to pay shipping i want it out of my garage
  9. goldsjos18

    auto locking hubs in a 1984 f250 ???

    ok so i picked up this 2004 dana 60 and im going to make it work fin in my truck. the guy that i bought the axle from said he just put new auto lockers in the hubs. so my question is can i rig up a solenoid from a 1999-2004 to work these hubs??? or is manual just a better way to go
  10. goldsjos18

    dana 60 from a 2004 worth 250$

    is a dana 60 ftont with 373 gears worth 250$ to you guys
  11. goldsjos18

    Zf5 transmission cooler...

    So my plan is to use a oil pump from summit racing https://www.summitracing.com/parts/til-40-524 and plumb into the ports on the radiator for an automatic transmission but my question is have any of you done this sort of thing with a zf5 speed also should I have the new pump ran off a temp...
  12. goldsjos18

    low Engine temp

    It’s impossible to get my 94.5 up to normal engine temperatures even after a 45 minute drive to work ... thermostat problem? With winter weather I would like my heater to work lol
  13. goldsjos18

    7.3 bucking under hard acceleration with a rough idle

    My 7.3 will buck under hard acceleration and has a rough idle.. it only bucks when your really getting into in around 2500 rpms. Theirs no check engine lights that shows up it bucks so violently it chirps the rear tires it’s fariy annoying and would like to figure this out I’m scratching my...
  14. goldsjos18

    water in fuel lines frozen

    well i got some water in my tank somehow and the truck picked up the water in the lines... well its getting to the freezing temps and the truck no longer starts pulled the fuel filter and the fuel bowl was empty so its not pumping fuel any way to get it to pump fuel without taking a torch to...
  15. goldsjos18

    luk clutch power rating

    what kind of power can a luk solid mass flywheel conversion hold?
  16. goldsjos18

    1984 ford f250 front brake questions...

    i was going to go in and to some break work on my truck and well when i took the tire off the front of truck the brake rotor seams to be behind the front hub..... is this a normal thing or did the previous owner screw stuff up?????? i dont have pictures at the moment
  17. goldsjos18

    Vacuum block for a 1995 7.3 powerstroke

    I need a vacuum block/ spliter for a 1995 7.3 psd as mine cracked and leaked and I don't have vacuum to my brake booster anymore
  18. goldsjos18

    Cab for a 7.3 powerstroke obs wanted

    I'm searching for a cab for an obs 7.3 powerstroke
  19. goldsjos18

    stuck manifold bolts

    ok so i have a 1994.5 psd and it has a major exhaust leak so im doing up pipes and maifolds vut the manifolds are rust welded into the block and i dont want to strip out the head of the bolt.any ideas?
  20. goldsjos18

    Air to air or water to air intercooler

    what's everyone's opinion on Jair to air intercoolers and water to air intercooler ? Pros and cons of each?
  21. goldsjos18

    1984 6.9 idi engine and 4 speed trans with transfer case

    i have a 1984 6.9 idi with i think 170k miles comes with original transmision and transfercase
  22. goldsjos18

    1984 7.3 powerstroke build

    All right guys so this is my first build thread. So for the last couple weeks I have been tearing down my 1984 6.9 idi f250 and a 1994.5 7.3 powerstroke. So far I have the front end of both trucks ripped apart fenders hood ect. I'm going to not only swap the engine and transmission but also the...
  23. goldsjos18

    fire wall questions

    hey guys im in the middle of a 7.3 psd engine swap and i just want to know if a fire wall that is in a 1995 will fit into a 1984 i would like to take the entire fire wall if i could because i also plan on swapping in the dash if you guys have any information on this kind of swap i would much...
  24. goldsjos18

    Old style banks turbo specs

    Does anyone have the specs for an old style banks turbo I'm trying to find a compressor wheel.....
  25. goldsjos18

    1984 f250 no start

    truck sputters but wont start glow plugs dont seem to be working either i need help as this is my work truck and daily driver

Latest posts

Forum statistics

Threads
91,306
Posts
1,130,031
Members
24,117
Latest member
olsen726

Members online

Total: 790 (members: 10, guests: 780)

Share this page

Top