Forums
New posts
Search forums
What's new
New posts
New resources
Latest activity
Resources
Latest reviews
Search resources
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
screwhead's latest activity
S
screwhead
reacted to
Old Goat's post
in the thread
New guy to the IDIs
with
Like
.
If you are going to replace the return lines, then you need to also replace the 2 Viton "O" Rings on the top of each Injector. You...
Apr 8, 2024
S
screwhead
reacted to
MC770's post
in the thread
New guy to the IDIs
with
Like
.
Solid points, no worries about you being 'picky' on my end. I'm here to learn what I can and get help from the vast pool of knowledge...
Apr 8, 2024
S
screwhead
reacted to
IDIBRONCO's post
in the thread
New guy to the IDIs
with
Like
.
Welcome Matt. Here's a couple of things that I picked up from your post. 1) Accuracy in describing your problems will help them be...
Apr 8, 2024
S
screwhead
reacted to
Agnem's post
in the thread
Introduction to the IDI Tech forums. All Newbies start here.
with
Like
.
Welcome to the OilBurners.net 1983 to 1994 IDI Technical discussion forum. This forum is for technical discussions relating to any F or...
Apr 8, 2024
S
screwhead
reacted to
Rocknit4x4's post
in the thread
Specialty Tools Needed for 7.3 Rebuild?
with
Like
.
I doubt anyone on this thread currently needs the info, but it might be helpful for anyone searching for specialty tools in the future...
Apr 5, 2024
S
screwhead
reacted to
franklin2's post
in the thread
Gear Rubbing Inside of Manual Hub
with
Like
.
#3123 is the needle bearing.
Apr 4, 2024
S
screwhead
replied to the thread
Gear Rubbing Inside of Manual Hub
.
@Rdnck84_03 There is definitely some play in the axle shaft/knuckle. I figured it was the u joint. It is much worse on the driver side...
Apr 4, 2024
S
screwhead
reacted to
Rdnck84_03's post
in the thread
Gear Rubbing Inside of Manual Hub
with
Like
.
Did you replace the needle bearing inside the inner side of the spindle that supports the half shaft? If not reach around and see if...
Apr 4, 2024
S
screwhead
replied to the thread
Gear Rubbing Inside of Manual Hub
.
Also only makes this noise when turning the hub/rotor backwards, whenever turning forward there is no noise.
Apr 4, 2024
S
screwhead
reacted to
Old Goat's post
in the thread
CDR valve - what is this part?
with
Like
.
As I remember when I replaced my CDR quite a few years ago. The old one had a metal tube that went into a gromet in the Valley Pan. It...
Apr 4, 2024
S
screwhead
reacted to
Jesus Freak's post
in the thread
Charging question
with
Like
.
The original wires have a really cool way of looking just fine but having a ton of green corrosion inside the end of the wire right next...
Apr 4, 2024
S
screwhead
reacted to
Nero's post
in the thread
High idle switch
with
Like
.
When the high idle switch fails, it'll fail in one of two ways. The electric part shorts out and it'll never work, or a groove has worn...
Apr 4, 2024
S
screwhead
posted the thread
Gear Rubbing Inside of Manual Hub
in
6.9L IH & 7.3L IDI Diesels
.
1993 F250 7.3 NA with Dana 50 and manual locking hubs. I just replaced rotors, calipers, brake pads, and bearings/races. When I put the...
Apr 4, 2024
S
screwhead
reacted to
XOLATEM's post
in the thread
Trailered home a 1989 F350 dump truck that looks great on the outside, but the 7.3 IDI is something else
with
Like
.
https://www.summitracing.com/parts/umi-01055 Since you are familiar with the Summit website...something like this will keep your shop...
Apr 2, 2024
S
screwhead
reacted to
IDIBRONCO's post
in the thread
Trailered home a 1989 F350 dump truck that looks great on the outside, but the 7.3 IDI is something else
with
Like
.
If you take it to a shop, they can remove the old cam bearings. You won't have to. If they're all pretty bad/nasty,greasy, it wouldn't...
Apr 2, 2024
Latest posts
Is it my alternator?
Latest: RSchanz
26 minutes ago
6.9L IH & 7.3L IDI Diesels
DB2 Fuel Intake Thread
Latest: divemaster5734
30 minutes ago
6.9L IH & 7.3L IDI Diesels
Afe air filter good/bad?
Latest: u2slow
Today at 3:18 PM
6.9L IH & 7.3L IDI Diesels
ATS 093 leaky slip joint repair
Latest: david85
Today at 2:58 PM
6.9L IH & 7.3L IDI Diesels
Ford Says "Hold My Beer"
Latest: Nero
Today at 2:36 PM
6.9L IH & 7.3L IDI Diesels
Forum statistics
Threads
91,315
Posts
1,130,191
Members
24,121
Latest member
720Diesel
Members online
rburt
RSchanz
divemaster5734
ttman4
mexicanjoe
Kdo58
BlindAmbition
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top