Recent content by Pearl_Diesel

  1. Pearl_Diesel

    Just double checking safe temps

    Alrighty, just installed my pyrometer over the weekend, an Autometer unit (wanted isspro, but this one'll work fine, and got a good deal on it) most of the time, temps stayed around 4-600, would peak to 8-900, and the time I tried to get them the highest, I was only able to peak to 1000, so i'm...
  2. Pearl_Diesel

    Best 6.9 block

    Smoke can be anything from bad injectors, bad pump, improper timing, or air in fuel. On mine, I installed injectors and replaced the pump and return lines, and it still smoked. Turns out the timing was advanced a hair too much, and it fixed it just fine. Starts and runs great, and gets less...
  3. Pearl_Diesel

    Pondering at work ?

    If you have an 87-91 series, I just took the plastic bulb cover off, and it's brighter than hell in the truck now.
  4. Pearl_Diesel

    rubber fuel injector lines

    I've seen return lines replaced with these type of lines, but not main hard lines. And Hydraulic lines withstand incredible amounts of though, and they're multiple steel braided lines, it might actually be plausible.
  5. Pearl_Diesel

    hypermax type s or pulse

    Haha and the propane was just in case you didn't make that 300 at the crank on the dyno, you could always give it a little snort and maybe tip the scales. :sly
  6. Pearl_Diesel

    hypermax type s or pulse

    I posted quite a while back on this, for one thing, 6-800 is probly not gonna happen without a major teardown, and really really special parts. I figured a nice conservative goal would be 300, and by my guesses, with a good turbo, head studs, a custom ground cam to help the turbo, moose...
  7. Pearl_Diesel

    Two Big Questions for you hardcore IDIers

    In my case, I just found a parts truck with 4.10 front and rear gears, and it was the easiest thing i've ever done. I went from a 1990 sterling 10.25/Dana 50 to a 1986 Dana 60/Dana 44HD, all I had to do was get new U bolts, unhook brakes, change yoke in rearend (wouldn't have to if same...
  8. Pearl_Diesel

    Few pics of my truck

    I think I would sacrifice not getting powdercoated just for the sake that you can get Humvee tires cheap for 16.5. 37's!!
  9. Pearl_Diesel

    Scout looks like.....a scout AGAIN!! =)

    YESSSSS:backoff:hail
  10. Pearl_Diesel

    Gas Burner Question

    I didn't know that you could squeeze 20 out of a 4.6 auto. the best i've ever seen anybody get around here is about 18, and nothing more.
  11. Pearl_Diesel

    new bumpers!!

    You used only 14-16 guage? Isn't that a little weak? I went for 1/8 inch with 4 inch square by 1/8 inch tubing behind it. So about 1/4 inch total, in diamond treadplate. It passed the sledgehammer test and the tree test. :D;Sweet
  12. Pearl_Diesel

    Aftermarket Tachometer Question

    Any factory tach sending unit from the IDI's will work, 83 6.9 all the way to 94 7.3 turbo
  13. Pearl_Diesel

    Aftermarket Tachometer Question

    Your injector pump housing should have a port in the top near the oil fill where the factory Tach sender goes in, just unscrew it and put a factory tach sender in there.
  14. Pearl_Diesel

    STACKS OR DUELS PIPES?

    if you've got a turbo, it doesn't matter. If you've got a n/a, I would just run duals out the back, there's no difference with stacks.
  15. Pearl_Diesel

    Brown Truck Under the Knife Project - Engine

    Tear that old mechanic a new one, and have him pay for replacement heads
See more

Latest posts

Forum statistics

Threads
91,328
Posts
1,130,440
Members
24,133
Latest member
Nanohawk

Members online

Total: 715 (members: 11, guests: 704)

Share this page

Top