Search results

  1. 1mouse3

    Three legged animal...

    I started by getting this outer pannel to fit better and could not use the stamped lip for the post, so that was cut. Also cut a slit and pinched the rear cornner, so the pannel would fit flush. Well flush is subjective, since the rear of the cab was beat up in the past. Then did the...
  2. 1mouse3

    Three legged animal...

    This piece of the rocker ait a lot of time to get out and free now So have it now in a state, I can build this section back up Do now have the rocker fitted in place with a few screews... And have the corner loosely in place, will get it fit better at a later time.
  3. 1mouse3

    Hydroboost Ghost

    Sound like air and have ran into it before on a obs/nbs chevys, but is rare to happen replacing lines. When happens, I will loosen the pressure lines one at a time so they weap fluid to get it to work. Never had the issue with my truck with a f-super hydro, then again I have a saginaw pump with...
  4. 1mouse3

    Three legged animal...

    I had some time to spend getting the rocker out today. Still need to get it off the front post, but at least I got the hard part out. Im going to have to make a few pieces, so can rebuild this section. Also found around a 1/4 inch of puddy, that repaired past damage. Im not sure how Im...
  5. 1mouse3

    Three legged animal...

    Thanks for the inspiration for just making something work. Iv been going over it trying to figer out a plan of attack and path to save as much of the orginal metal. Like that rear post patch piece, I cant get around not using it beacuse how it is part the structure. Im going to have to rebend it...
  6. 1mouse3

    Three legged animal...

    Im not sure how Im to drag a parts truck home from out there.
  7. 1mouse3

    Three legged animal...

    I see where your getting with this and seems to be the only option to fix this. Im not sure I saw any trucks at the yard the other day I was there to be able to salvage what I need. So need to do as you say and start hording stuff when is found for the body.
  8. 1mouse3

    Three legged animal...

    I started opening the can of worms and pulled out the self destructive foam. The inner panel will need patch but need to think on it, since in a sandwich. That hole, need to bends some metal to make something work. Would like to have been able to get the piece of metal between the rocker...
  9. 1mouse3

    1999 power stroke engine swap options.

    Id say a dt360 since the same size as a 12v and you can get a adaptor for one adaptor You trying to be more needy than me?:rotflmao And way do you need a fat SD over a 80s dodge d300 thats ment to fit a cummins?
  10. 1mouse3

    Three legged animal...

    This is the limit to what lmc sell and bronco graveyard is the same stock, there was one other place listing the same stuff as well. page 12 page 15 This is as much metal as I could get from lmc, so short inner post sections. There is other sections needed but can make flat metal work in...
  11. 1mouse3

    Project Thread: 89 F250 Franken Truck

    You can do 9/16 but I dont recomend it. This is a "dont try this home" video on doing said task.
  12. 1mouse3

    Three legged animal...

    Well time is about to past to shove the replacement engine in but should fix something so is easyer than last time. One the cab mounts are past due for replacement and it limits how high I can raise the transmission, the engine fought me last time to fall in place because of this. I have ordered...
  13. 1mouse3

    slipping into insanity

    I finaly got the 31 spline axles on hand to replace the 28 ones, should of had them sooner. They are ment for a bronco, any option for this truck is non existent. Also got a spool as well and have that installed. Glad that I went this route, the old center was rejecting the welds. Not...
  14. 1mouse3

    flux capacitor

    -Drool
  15. 1mouse3

    flux capacitor

    More stuff... More time in the wood shop... Leave me with something that needs fiberglass.
  16. 1mouse3

    slipping into insanity

    Well she found something else to brake... :bail This time its a axle shaft and it is not plausible to get the posi aprt to drive the end out, its drilled and welded solid. So guess I have to spend the money on a spool and upgrade to 31 spline over 28.
  17. 1mouse3

    Jesus Freak's WMO tow truck

    I think that was still sitting in the parts bin at the time. Yes its a good way to wash her and parts need to fit some how.
  18. 1mouse3

    driveshaft shenanigans

    I got around to unboxing the replacement yoke, its not a 100% match but will work. So the axle is done and see can move under her own power again.
  19. 1mouse3

    Jesus Freak's WMO tow truck

    But fording is fun... :rotflmao
  20. 1mouse3

    ardunio madness

    The main harness to the black box is made.
  21. 1mouse3

    flux capacitor

    A tray to hide stuff is served.. Then its a balancing act on all thread... To get me a set closer to completion.
  22. 1mouse3

    flux capacitor

    Door are done and not looking too out of place.
  23. 1mouse3

    2nd blown oil filter gasket and coolant mixing with oil? Help with isolating the causes?

    What I suspect is cause of the blowing of the oil filter o-ring is this regulator is stuck. You will have to pull the cooler to get at it, in the rear head there is a staked in bit you have to get out with say a chisel. At this point you might want to think about replacing the o-rings for the...
  24. 1mouse3

    flux capacitor

    I spent some time wrapping presents to myself, hope I get something good... :joker:
  25. 1mouse3

    flux capacitor

    There ready for display trial... -Drool
View older results

Latest posts

Forum statistics

Threads
92,996
Posts
1,155,941
Members
26,574
Latest member
abcdefg

Members online

Total: 1,832 (members: 3, guests: 1,829)

Share this page

Top