Search results

  1. aggiediesel01

    Need help with CDR grommet (Rubber piece) on 92 7.3L ATS Turbo setup

    What idi bronco describes is what I'm familiar with on ATS and factory turbo trucks. I know ATS used that special CDR valve cover that was originally an IH part as part of their kit but the few that I've seen have a moulded rubber hose that goes from a nipple on the intake casting to a nipple on...
  2. aggiediesel01

    Crewcab Project

    Where were they on the injectors? Looks kind of like an oring was sheared during install and the sheared part was squished by the body for years
  3. aggiediesel01

    My Turbo Pipes

    Banks and ATS each always claimed their turbo systems added about 50% more hp and torque to the wheels over stock and often published Dyno graphs purporting to show that. The ford factory system was basically a detuned ATS system with virtually no increase in fuel delivery. It had to be detuned...
  4. aggiediesel01

    Automatic to manual swap

    There may be a spacer between the flexplate and crank that has to be removed if going from auto to manual also. I'm not sure if this is true on the c6 like it is on the later e4od but maybe someone else can clarify.
  5. aggiediesel01

    Are these adaptors?

    Out of curiousity do you know what pressure the push-lok style fittings are good for?
  6. aggiediesel01

    Glowshift Gauges?

    I really like that GlowShift offers a specific pillar pod for the '91 and older trucks up to 4 gauges on the pillar. I don't think anyone else offers one at all and it so nice to actually have one that fits rather than trying to mash the OBS one into place on the older pillars. I don't know...
  7. aggiediesel01

    My Turbo Pipes

    Looks very nice, be sure to get a heat shield sock for your slave cylinder, turbo trucks are known for cooking these after a few years of higher than normal egts.
  8. aggiediesel01

    Diagnosing OD Flashing when shifting to 3rd. Brake light circuit?

    For the brake controller, it would depend on how someone wired it in. If your truck came with the factory tow pkg then the chassis wiring was setup to have a controller added without affecting any circuit in the truck. If it was added without that package then it could possibly be contributing...
  9. aggiediesel01

    Manual Transmission Oil Cooler

    Definitely interested in pictures, please share them. Sounds like it could be a good add to any truck hauling often.
  10. aggiediesel01

    ZF5 crossmember question. I’ve looked everywhere..

    @CameronB i sent you another PM and a post on your profile page.
  11. aggiediesel01

    Ok going full Dr house on this bitch

    When mine was behaving similarly it turned out to be an internal issue with the power circuit inside the PCM. The main processor was losing power intermitantly. Mine would randomly, occasionally blip off and then come back until it finally got really bad and would stumble and restart and then...
  12. aggiediesel01

    Extended Idle Time.....

    On the SuperDuty trucks I'm pretty sure there is a pre installed circuit/blunt cut wire in your under dash harness that you can connect to one of the upfitter switches or any switch really to create high idle. There's plenty of information about that wire and how to connect it via google. You...
  13. aggiediesel01

    Single Piece driveshaft for 7.3 idi non turbo, 4x4, zf5

    There’s a guy on here that did a single piece drive shaft for one of his customers in a truck similar to yours. You can read what he did and how it came out in the link. I think the customer may have had to change the angle due to some minor vibrations when unloaded vs loaded or something along...
  14. aggiediesel01

    ZF5 crossmember question. I’ve looked everywhere..

    Cameron; I sent you a PM, if you can, let’s discuss it there.
  15. aggiediesel01

    Bandaid on a bullet wound

    Here's a front seal tool that a member built to use the three nuts welded to the front plate for this purpose. I believe there's an option on the front seal to get a wear sleeve if needed as well. There may be a reference to the seal info in that thread...
  16. aggiediesel01

    Bandaid on a bullet wound

    All the rubber seals and gaskets for the turbo system you may need can be sourced from a couple forum members here. Russrepair.com is the closest to you over in Oregon and classicdieseldesigns.com also has many of these parts as well they’re just a ways away from you down here in TX. If you’ve...
  17. aggiediesel01

    New air cleaner lid?

    Years ago Banks made a taller cast aluminum lid with a custom k&n filter as an upgrade. You could check to see if it’s still available. Maybe someone on eBay or Marketplace has one of those or an original. If not, I wouldn’t break out the welder for this, might burn more holes than close up. I...
  18. aggiediesel01

    Where to get an original starter rebuilt?

    That and a big sagging shelf of alternator and starter carcasses behind the front counter exactly describes the shop I’ve used several times here in my area. And years later all their rebuilds are still going.
  19. aggiediesel01

    Source for new 7.3 IDI engine?

    Try www.car-part.com put in the basics of what you’re looking for an you might find a decent low to avg mile engine in Idaho or eastern Washington or Oregon.
  20. aggiediesel01

    Where to get an original starter rebuilt?

    Here’s the post with the name of the shop in B/CS https://www.oilburners.net/threads/starter-upgrade.87120/post-1047195
  21. aggiediesel01

    Where to get an original starter rebuilt?

    If you’re still in central Texas there’s a number of good small shops. A couple in Waco last time I was there, Austin has a couple on the east side if I remember correctly, Houston has a bunch in south Houston, College Station/Bryan has a good one, in fact that one used to sell a special built...
  22. aggiediesel01

    gauges died today

    I have a set of ‘94 pdf manuals that cover both IDI and DI. You can download the EVTM and see if it’s the same as your ‘95. Might be close enough. https://drive.google.com/drive/folders/10p8-zgMZIlwXpPflSoTzqviEuWwMARF7
  23. aggiediesel01

    idi parts compatibility with PSD

    if your ‘92 has the serpentine belt setup then your 3g alternator should be the same except for the pulley, same with the vacuum pump (except maybe the hose nipple orientation. If both trans are auto, the ‘92 could be put in the ‘96 in a pinch but the internals are not as good. The instrument...
  24. aggiediesel01

    International Fuel Systems

    If you can be without the truck for a week or so, I believe Wes of CDD has an inspection service where he can put your pump and injectors on his stand and make sure it's working correctly instead of just jumping in for a rebuild. Or there's likely a fuel injection shop somewhere near you that...
  25. aggiediesel01

    BILLOWING white smoke

    If you’re confused about where your leak out the pan went, chalk it up to corrosion. The amount of time you’ve had this issue is more than enough for surface rust to set in, starting to block off the leak. Put it back together without fixing it and the heat, pressure, vibration will get you...

Latest posts

Forum statistics

Threads
92,929
Posts
1,155,105
Members
26,430
Latest member
Brownlee5212

Members online

Total: 690 (members: 1, guests: 689)

Share this page

Top