Recent content by Tumbleweed210
-
-
Done trying to keep up with this...
Well...alrrighty then...not even crickets on this'n. Scrap-yard it is.- Tumbleweed210
- Post #2
- Forum: Marketplace
-
Done trying to keep up with this...
FOR SALE BEST OFFER: The truck in my sig 1993 F-Superduty 7.3 IDIT, factory turbo w/upgraded wheel (redone by Type4 ), Zf-5, new Spicer U-joints, 10 ft flat bed, boost and egt guages... I just can't seem to get this truck where I need it to be on a part time job, going to school full time...so...- Tumbleweed210
- Thread
- Replies: 6
- Forum: Marketplace
-
Texas IDI Roundup- Dyno day and Show & Shine
Wish I could make it down there Wes...but over the last three and a half weeks the truck's gone to leaking oil outta damn near EVERY gasketed surface (can't go fifty miles without needing 2~3 quarts), injectors hanging open~or~shut at every traffic light~or~stop sign, oh and probably more than a...- Tumbleweed210
- Post #26
- Forum: Events and Get togethers
-
Any suggestions on which SMF kit?
I'm all ears...93 IDIT DMF and associated parts are now scattered down Hwy84 somewhere east of Waco... And I'm not sure which SMF Kit to get?- Tumbleweed210
- Thread
- Replies: 3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Fuel Line quick connectors?
So what you're really saying...is that you don't know what type ends Ford used on these trucks... Because the ones I've got are all BROKEN and no amount of clips or O-rangs is gonna fix that. The ends need replacing... But thanks for the input...- Tumbleweed210
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Hi from NC
Welcome to OB...one of the best, if not THE best forum for diesel info and discussions.- Tumbleweed210
- Post #2
- Forum: Introduction
-
-
Fuel Line quick connectors?
Yeppers I put some of those in last year...then the O-rings started weeping. Tried pickin them out...PITA...but got them replaced. Wound up that I put NBR's in and found out they don't play nicely with our fuel of choice. Went back to put Dorman Vitons in, and those were too loose? Sealed...- Tumbleweed210
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Cold air intake advice?
Use the SEARCH BAR....FIND the threads...there's a few really good ones 'round this here furrum. Cheers!- Tumbleweed210
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Fuel Line quick connectors?
I'm trying to fix all the fuel lines from both tanks, up to the stock tank selector valve... Does anyone know if these are the right type fuel quick-connects for the '93 Cab-n-Chassis 7.3L IDIT???:dunno Dorman 800-086 Fuel Line Quick Connector for 3/8 In. Steel to 3/8 In. Nylon Tubing, And...- Tumbleweed210
- Thread
- Replies: 6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Looking for fusible links!!!!
The only fusibles that I could find on mine were at the ends of the double wire (one ring connector -two links going into one wire...IIRC) that goes between the glow plug controller and starter relay (Right fender), and the starter relay to engine wiring harness (I think it goes all the way...- Tumbleweed210
- Post #21
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Looking for fusible links!!!!
Had the same issue...and it turned out to be one of the Maxi-fuses in the under hood "distribution box". You should be able to Google a diagram for your year/model.- Tumbleweed210
- Post #14
- Forum: 6.9L IH & 7.3L IDI Diesels
-
My arduino gauge project
Not intending to hijack this th thread...hoping to add to the conversation. hang on ...gots to git up on me soap box...ahh thets better... I must say that I am (and maybe others) somewhat enamored by the sweep of an analog tach...;Really...and the factory zpeedo seems to work well for me too...- Tumbleweed210
- Post #27
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Knocking at higher end rpm ?
Sub'd...:popcorn...- Tumbleweed210
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
