Recent content by Fasterthanyou925
-
White smoke under load.
Determined it was a bad IPR connector in conjunction with dying batteries and oil in the ICP. The truck runs awesome again. Sent from my Z812 using Tapatalk- Fasterthanyou925
- Post #24
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
She fired off today after 2 new batteries and a new updated IPR connector from international. Ran great for about 45 minutes then started bogging again. I had the ICP plugged in during that time (known to be bad) so I'm going to unplug it in the morning and see how she fares! Sent from my Z812...- Fasterthanyou925
- Post #22
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Tomorrow morning will tell all so long as this storm doesn't come in (I'm in rural North Texas, weather can get really crappy, really fast). BTW, here's the truck in question. Traded it for a Tahoe I was into for $2200 (but was worth more), plus dude gave me $200 and a nice .40 subcompact Sent...- Fasterthanyou925
- Post #21
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Yes, it sprayed fuel all over me...cap was under extremely high pressure and very full. I've done some reading, I'm going to check the IPR tomorrow and HPOP level. But I agree, I think I'm definitely going to have to get a scanner on it. Btw the WTS light is working, tach works when cranking as...- Fasterthanyou925
- Post #19
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Disconnected ICP sensor and went for test drive, it ran GREAT then died. Now it cranks but will not start! Sent from my Z812 using Tapatalk- Fasterthanyou925
- Post #17
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
No more smoke but today a new issue came up; I was driving up a hill at low speed and it started sputtering. Pulled over, turned it off and called my wife to bring me fuel as I figured the gauge was just wrong. Just for giggles I fired it up and it ran fine...so I figured I'll just drive it...- Fasterthanyou925
- Post #16
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Found today the coolant is a little lower than I'd like. Injectors seem fine via scanner and NO oil from the turbo. I'm thinking o-rings or cups? Sent from my Z812 using Tapatalk- Fasterthanyou925
- Post #12
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Ok cool. I'll investigate and report back. Thanks for the help. Sent from my Z812 using Tapatalk- Fasterthanyou925
- Post #9
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Yeah that's what I'm hoping for. I'm going to run by my buddies shop tomorrow and see if I can test the injectors if there's no oil hemmoring. How much oil is too much? Sent from my Z812 using Tapatalk- Fasterthanyou925
- Post #7
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
That's true. I'm a very experienced gasser guy, but have never really had to do a whole lot to my other diesels as far as diagnostics go...I think the most I've had to do was pull my ZF-5 from my IDI to do the stupid freeze plug behind the flywheel. I'll pull the DP tomorrow and check for oil as...- Fasterthanyou925
- Post #5
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Turbo seals? It's pure white smoke, not blue and does not smell like oil, raw fuel, or coolant... Sent from my Z812 using Tapatalk- Fasterthanyou925
- Post #3
- Forum: 7.3L Powerstroke Diesels
-
White smoke under load.
Just picked up a 99' PSD that is bone stock. Truck runs awesome, gets great mileage. injectors and cups done 5k ago with receipts. My wife was following my last night and said it was blowing smoke so I had her drive and followed her and sure enough; it's definitely white smoking under load and...- Fasterthanyou925
- Thread
- Replies: 23
- Forum: 7.3L Powerstroke Diesels
-
Pulling ZF-5 for freeze plug replacement
I agree about the bolts, good insight. My issue at this point is I did NOT buy a clutch since funds don't permit at this time so I don't have an alignment tool...parts house said the soonest I could get one is a week out and I need my truck back yesterday... Any tips on doing it w/o the tool?- Fasterthanyou925
- Post #41
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Pulling ZF-5 for freeze plug replacement
Will do. Any thoughts on getting this bad boy up into position? I'm having my wife go pick up some long bolts to line the bell housing back up. I am still stuck with a floor jack for this though, I can't find a trans jack anywhere for borrow or rental...not going to buy one I'm hoping this will...- Fasterthanyou925
- Post #37
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Pulling ZF-5 for freeze plug replacement
Now tonight hopefully I can git-r-dun and running again...hopefully- Fasterthanyou925
- Post #35
- Forum: 6.9L IH & 7.3L IDI Diesels
