Register to remove these ads



Results 1 to 7 of 7

Thread: ebpv delete instructions?

  1. #1
    What Log Book???? apextrans's Avatar
    Join Date
    Jan 2005
    Location
    Fallston, MD
    Posts
    1,613
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default ebpv delete instructions?


    I can't find 'em anywhere on here. Anybody got a link? Help a fella out. Thanks
    Scott
    1997 Ford F-350 7.3 PSD XLT CC LB SRW 4x4
    Bean's Stage 1's, Tubzz tunes - Van Aiken chip, Stealth SRP1, Bean's Modded IDM, Dominator 66, Shimmed FPR, Intercooled, CCV Mod, Bulletproof E4OD, 6.0 Tranny Cooler Mod, Tymar, MBRP 4", Sky RSK, ISSPRO EV2 gauges, fresh paint, Nitto 305's on stripped & polished OEM Alcoas

    SOLD-2003 Ford F-250 7.3 PSD Lariat CC SRW 4x4
    Modded up pretty good with help fromBeans Diesel Performance

    SOLD- 1988 F-350 7.3 CC SRW 4X4
    Modded way up for an IDI

    2008 Cherokee 295B Fifth Wheel Trailer

    Bean's Diesel Performance

    #61

    My Photos

  2. #2
    Stroker Mike's Avatar
    Join Date
    Mar 2004
    Location
    Cora
    Posts
    12,382
    Thanks
    9
    Thanked 86 Times in 36 Posts

    Default

    You want to gut it Scott?

  3. #3
    What Log Book???? apextrans's Avatar
    Join Date
    Jan 2005
    Location
    Fallston, MD
    Posts
    1,613
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    yeah. Butterfly valve (& the shaft) & the pedistal mod too. Putting a Dominator 66 on today & want unrestricted flow on the exhaust side. I sent you a PM to the same effect. Thanks
    Scott
    1997 Ford F-350 7.3 PSD XLT CC LB SRW 4x4
    Bean's Stage 1's, Tubzz tunes - Van Aiken chip, Stealth SRP1, Bean's Modded IDM, Dominator 66, Shimmed FPR, Intercooled, CCV Mod, Bulletproof E4OD, 6.0 Tranny Cooler Mod, Tymar, MBRP 4", Sky RSK, ISSPRO EV2 gauges, fresh paint, Nitto 305's on stripped & polished OEM Alcoas

    SOLD-2003 Ford F-250 7.3 PSD Lariat CC SRW 4x4
    Modded up pretty good with help fromBeans Diesel Performance

    SOLD- 1988 F-350 7.3 CC SRW 4X4
    Modded way up for an IDI

    2008 Cherokee 295B Fifth Wheel Trailer

    Bean's Diesel Performance

    #61

    My Photos

  4. #4
    Stroker Mike's Avatar
    Join Date
    Mar 2004
    Location
    Cora
    Posts
    12,382
    Thanks
    9
    Thanked 86 Times in 36 Posts

    Default

    I will assume youre going to remove turbo from engine then.


    You can see the butterfly housing (upside down in this pic) unbolted from the turbo here. Unhook the actuator arm, take a die grinder and grind off the two rivets that hold the butterfly to the shaft. Drive the shaft out of the housing and get two 3/4 inch freeze plugs to drive in the holes where the shaft was. Just that simple, valve is no longer a restriction.




    In this picture you can see the pedestal unbolted off the bottom of the turbo, on the back side of the actuator there will be a snap ring, remove it and pull the back cap off of the actuator and pull the valve out of the barrel. Flip the pedestal over, drill and tap the arm exit hole for a 1/4 inch pipe plug. Insert pipe plug and reassemble everything. Enjoy your new found unrestricted exhaust.




    Here is a link to an article on turbo removal. Turbo Removal WIKI

  5. #5
    the misanthrope hheynow's Avatar
    Join Date
    Mar 2004
    Location
    SF Bay Area
    Posts
    6,083
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Mine is tied open with a piece of wire but there is a very tiny oil drip coming from where the rod connects to the turbo. Not a big drip but should I be concerned? Will it damage anything if I do nothing?
    The only pony tailed grease driving left coast liberal at OB and proud of it.
    Without my $.02 you guys would be lost down a dead end road.
    1997 F-350 Powerstroke - PlantDrive VO Kit - 333K miles
    1984 Mercedes €uro 300D NA - Custom VO Two Tank - 166K miles
    Running on Veg Oil and Biodiesel since May '06


    Quote Originally Posted by wreckerman893
    Just more positive proof that the intelligence is being bred out of the human race at an alarming rate.

    This is why some people should be sterilized at birth.
    I can easily name a few!

  6. #6
    Stroker Mike's Avatar
    Join Date
    Mar 2004
    Location
    Cora
    Posts
    12,382
    Thanks
    9
    Thanked 86 Times in 36 Posts

    Default

    Its going to make an oil slick in the valley and it will get worse, eventually it will begin to run down the back of the block and she'll mark her spot but other than that you shouldn't see any physical or mechanical harm come of it Richard.

  7. #7
    Say what?!?! EMD_DRIVER's Avatar
    Join Date
    Jun 2008
    Location
    Martinsburg, WV
    Posts
    1,805
    Thanks
    73
    Thanked 13 Times in 4 Posts

    Default

    Thanks for the info Mike...

    I need to replace my up pipe donuts and thought about doing the ebpv delete as well...

    Do I need to remove the turbo, to change the donuts?

    Sorry for that last question being a hijack...


    Hijack off now!
    Gary



    God, please bless the USA.

    11 F250 CC LB 6.7
    4x4 auto 3.31LS gears

    99 CC 7.3
    4x4 auto 3.73s, with training wheels, 6637 intake, RDT, AD injectors, 4" exhaust, DP tuner, Regulated Return, a few gauges, '06 interior, '04 springs, '02 mirrors and shiny hubcaps.. 321,000 miles and counting!

    *SOLD* 97 F350 7.3 PSD CC XLT, E4OD, 4.10, 4x4, Water Injection, 3" Downpipe, 6637 Intake, EBPV delete, The Blue one.. 211,000 miles

    2003 Sunline F-344 SR Solaris 35' 5th Wheel..

    2002 VW Jetta TDI 1.9 L4 auto 266,000 miles




Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •