One decent truck out of two.

89Laredo

Underemployed
Joined
Nov 10, 2013
Posts
650
Reaction score
69
Location
Not Canada
Well unless someone has a better idea I guess Im slapping this engine back together... I have NOS Ford bearings and crank seals ordered, a Felpro IDIT gasket set, NOS IH thermostat, and a set of used rockers slightly better than what I had..
Im trying to decide what to do about the heads. One head has a good casting afaik but one chipped valve. The other head has all the ***** valve stems and Im pretty sure I saw a tiny crack between valves on one cylinder.

I REALLY dont want to spend a bunch of extra money, this was supposed to be a $200 gasket job, but should I just bend over and buy a set of 2 heads from CHI for like $1300?

My other thought is buy ONE head from CHI, and hand lap a used valve into the other head.
 
Last edited:

Nero

IDI enthusiast to the max
Joined
Jan 3, 2022
Posts
4,320
Reaction score
4,869
Location
OR
The cylinders by picture look okay. If the one head looks alright, I'd clean it and slap it back on, no need to replace good parts.

Replace the one head and the bad rocker, and send it. It's what I would do if it was my rig.
 

89Laredo

Underemployed
Joined
Nov 10, 2013
Posts
650
Reaction score
69
Location
Not Canada
Cylinders and pistons are about the only thing good on this engine lol

Im just mainly worried about this valve. You would leave it alone?
Looking at this pic again, I gotta check out that dark spot in the seat too...
You must be registered for see images attach



Im not sure what happened to the engine but seems like it was neglected, bearings look like theyve had grit run through them but surprisingly the crank looks/feels Ok-ish.

Im also wondering if maybe the timing was advanced too far and maybe contributed to the head problems? At very least, Im gonna back it off a little from where it was set when I tore it apart. But maybe if I only buy one head I will spend the money on a timing meter.
You must be registered for see images attach


You must be registered for see images attach
 

rreegg

IDI n TDI
Supporting Member
Joined
Feb 10, 2022
Posts
753
Reaction score
450
Location
Puget Sound
Cylinders and pistons are about the only thing good on this engine lol

Im just mainly worried about this valve. You would leave it alone?
Looking at this pic again, I gotta check out that dark spot in the seat too...
You must be registered for see images attach



Im not sure what happened to the engine but seems like it was neglected, bearings look like theyve had grit run through them but surprisingly the crank looks/feels Ok-ish.

You must be registered for see images attach


You must be registered for see images attach
Re valve: I’m not experienced in this realm but my gut says firm data like a compression test might be more reliable than visual inspections on this one. AKA no idea but seems like it’s tough to compression test at this stage of the re/build

Very curious what other folks think though based on their priors
 

Nero

IDI enthusiast to the max
Joined
Jan 3, 2022
Posts
4,320
Reaction score
4,869
Location
OR
Damaged valve is a no go. Does not meet reuse is the verbiage I use at work. Is that on the 'good' head? If so I'd remove and inspect the valve seat.

Too advanced timing can result in running hot as well.
 

89Laredo

Underemployed
Joined
Nov 10, 2013
Posts
650
Reaction score
69
Location
Not Canada
Yes thats the good head.
Yeah Im gonna check it out. My back has been screwed up again so havent been working on it, and been waiting for parts. At this point Im kinda wishing I wouldnt have bought this engine and just tore my original 6.9 apart. I guess its still a possibility to do that, assuming the crank is standard since I already bought std bearings. That thing needs a ton of work too though. It burned about a gallon of oil in 100 miles, it might have a bent rod from when I hydrolocked it, and I bet its rusty on the bottom end from sitting full of coolant.
 

89Laredo

Underemployed
Joined
Nov 10, 2013
Posts
650
Reaction score
69
Location
Not Canada
That chipped valve from the "good" head has about a 1/16 deep groove worn into it. Umbrella seal was crunchy and easily broken.
I'm gonna say both heads are unusable as is.
FFS.
seriously considering tearing the 6.9 apart just to look at it.


You must be registered for see images attach
 
Last edited:

lotzagoodstuff

Full Access Member
Joined
May 19, 2007
Posts
2,905
Reaction score
886
Location
Carmel, IN
I know you aren't trying to spend any more money, but I think I'd put a set of used but inspected heads on it. I see lots of IDI's getting parted out on FB Marketplace here in Indiana for pretty reasonable prices. I know you've been building one good truck out of two, but might be time to change to "one good engine out of three". Not being a smarta$$ just saying sometimes you gotta add a third type of apples when you are making pie and run out of the first two varieties.

Keep at it: your resurrection of this truck is inspiring.
 

Forum statistics

Threads
93,197
Posts
1,158,282
Members
26,623
Latest member
bneumann22

Members online

Top