Search results

  1. redneckaggie

    inputs to control turbo

    Been gone for a while. I have previously been in the idi forum. I have traded the idi to my dad for a 92 12 valve. I have also recently bought an 04 4x4 crewcab 6.0. I eventually plan to swap the 5.9 into the 04. When I do I was thinking why not go vgt on the 12 valve. I will already have...
  2. redneckaggie

    glow plug controller troubleshooting

    Ok guys I have been having a little trouble with my gps On the first turn of the key of the day the glow plugs do not cycle. after it is started and ran for a few minutes I can turn it off and turn the key to on and the gps cycle normally. If I let it sit for more than 6 hours they go back to...
  3. redneckaggie

    permagrin enable

    well just drove the idi for the first time since turning it into a project about a year ago. I repaired core support, body lift, redid the whole interior besides carpet (still looking for off road carpet made to fit), added an ats 093 turbo, coolant filter, and several other little things I...
  4. redneckaggie

    throttle cable routing with 093 turbo

    Buttoning up on the ford from turbo, coolant filter and interior refreshen project and about the only thing I have left is a few small wiring additions, door panel installation, and amp/subs. I was glancing through the engine bay today and saw that I had not reconnected my throttle cable. I...
  5. redneckaggie

    coolant filter

    Before I filled the coolant back up I was looking at the possibility of putting a coolant filter on it. i searched around and found this article http://www.oilburners.net/articles/coolfilter4.html I see in the article that he hooked it up where the filter coolant flows around the filter...
  6. redneckaggie

    fender alignment questions

    where are the bolts to adjust fender alignment? I know about the ones on the core support and up top by the door but are there any other bolts? I loosened all of them that I saw and the fender wouldnt move. I know dumb question but im really sorry I looked all over and probably missed the...
  7. redneckaggie

    ip inlet thread type

    I am trying to make a an flexible line for the fuel feed past the filter to the ip. I would like to know what threads are on the fuel inlet for the ip, I know that it is a compression fitting that the hard line connects to but I am talking about the other side of that adapter, it appears to be...
  8. redneckaggie

    glow plug controller wiringc

    while prepping for my turbo install I repositioned the wires on the gpc. I thought I had got them all back on there but now I looked back there just before I bolted the turbo to the drain and I noticed a loose wire hanging back there. The black wire comming from the back of the controller is...
  9. redneckaggie

    is this a coolant port

    trying to keep the factory sensor as well as hook up my aftermarket coolant temp sensor. I see the square headed plug at the rear of the drivers side head but I cant seem to get it out. Then I notice a socket head plug at the very rear of the engine at the top, 3/8s extension plugged right...
  10. redneckaggie

    relocating gp controller for turbo install

    I am down to wiring in the engine bay before i can install my turbo and I am curious if anyone has installed an 093 without relocating glowplug controller. I just read the ats install instructions and the only mention of relocating is rerouting the throttle cables and the fuel lines, which I...
  11. redneckaggie

    input on dyeing interior

    Need some input or thoughts, i have found a few dashes locally but so far nothing blue, I have found several gray ones so has anyone had good luck with dyes for interior plastic, if so what brand and where did you get it, I would like something extremely close to the factory blue so I dont have...
  12. redneckaggie

    I need a dash

    Hey guys I am searching around for a dash, preferably blue,, no major cracks, mine currently has the mounts busted. I have combed craigslist and ebay and have talked to a few folks around here, i found two on ebay but they were wanting way to much for them
  13. redneckaggie

    request for single cab guys

    ok guys I took some dimensions for my speaker box before I pulled the seat and sent it to the upholstery shop but I seemed to have lost them. Could someone please give me dimensions from the seat to the back of the cab at the top of the ledge, from the top of the ledge to the beggining of the...
  14. redneckaggie

    help with ford pns

    I am trying to figure out what two items are underneath my dash. I would like to know because if they have anything to do with the radio I have bypassed them and they can come out of there to make routing wires easier. both were mounted just drivers side of the radio up inside the dash...
  15. redneckaggie

    dome light question

    does anyone have good electrical prints of what pin on the headlight switch is the outgoing power to the interior dome light? In other words what wire gets power when you twist the knob all the way over past the click and the dome light should come on. Wire color would be nice as well. My...
  16. redneckaggie

    my version of the tank vent mod

    well gentleman I am in the process of doing many things to the truck and first on the list was the fuel selector valves, tank vent, and showerheads. I pulled the sending units and tested them with an ohm meter and they seemed fine, spliced fuel hose onto the pickup with a beak cut into the...
  17. redneckaggie

    filler neck mod question

    I have read about the filler neck mod and everyone keeps linking the same article from diesel stop where the guy plainly says that the mod caused vacum in the tanks. I kind of have the idea of doing something similar. Here is the idea. I will install a fitting in the grommet for the roll...
  18. redneckaggie

    Temp switch for gp's

    Hey guys I have been tossing around the idea of finding a temp switch to install that would kill the relay power to the gpc so that glow plugs will not cycle when coolant is above a certain temp. I searched google and all I can seem to find in a reasonable price range(< $75) is these snap...
  19. redneckaggie

    fsv not working

    Anybody got electrical schematics for the fsv valve. mine is not swapping, I started simple and checked the fuse and it was fine, I am going to pull the fuse box and check wiring into the back of it asap because my heater recently melted its section of the box, might even go to an aftermarket...
  20. redneckaggie

    blower motor question

    hey all my blower motor quit working today. It does not come on on any speed and the voltmeter in the dash does not show any load when it is turned on. figured it was something easy and checked the fuse and I found it melted into the box. replaced it and the motor still does nothing on any...
  21. redneckaggie

    high idle/ cold advance

    lately my high idle and cold advance have not been working, I jumpered both of them manually with 12 vdc and they work fine. I have checked the continuity of the sensor in the front drivers side of head an it had no continuity to ground when engine was cold. I was under the impression that...
  22. redneckaggie

    antilock brake light

    Need some info on where the antilock light on the dash gets its signal from. I have no braking problems but that light just stays on all the time now and I am curious what sensor feeds power to it? It is not the red light that comes on with the parking brake but rather the yellow antilock...
  23. redneckaggie

    minimum rdt hose size

    Hey guys gonna install my turbo soon. It is a factory turbo but I dont have the valve cover with the hole for a cdr so I was going to just run my rdt from a different location, I have a nipple welded onto the front of the plate over the ip gear bolts and was just going to use that and route it...
  24. redneckaggie

    truck dies?

    recently I have been having a problem with the truck dieing as it tries to return to idle. If you are driving along at rpm it runs perfectly fine and does not starve for fuel(surge). when you punch the clutch to stop and the engine tries to return to idle it will bog hard as it hits idle and...
  25. redneckaggie

    headlight connectors

    ok I know I read somewhere on here that we could use a headlight connector for a big truck that would have 12 awg wire coming off of it but does anyone know the make and model of the "big truck" to ask for or even a part number. My local napa just gives me blank stares when I went in to search...

Latest posts

Forum statistics

Threads
91,275
Posts
1,129,667
Members
24,098
Latest member
William88

Members online

Total: 406 (members: 2, guests: 404)

Share this page

Top