Search results

  1. 645E3B

    The Official "Show Us Your Ride" pictures of member's trucks thread.

    I got the truck out of southern Oregon, one of the it just needs a little TLC you need to understand one person’s idea and yours may differ greatly Before and after a lot of work
  2. 645E3B

    IDI Parts

    What are you asking for the injectors
  3. 645E3B

    16-567 EMD question

    The lower end of your engine will handle anything you can build, the rods , rod bearings, and mains are the same on the 8 cylinder blown engine to the turbocharged 20 cylinder 645E3B with 3600 hp A 16 567 D3 turbocharged engine was rated at 2000 hp and the engine blocks are all welded steel...
  4. 645E3B

    16-567 EMD question

    I think that you have a 16 567 D3, 567 power assy. Are not as plentiful as they were but you can install 645 power assy. in any EMD block after ”C” type and you can use with the turbocharger you will not need to change to roots blowers.
  5. 645E3B

    OIL PAN MODIFICATION FOR COLD WEATHER STARTING

    I have worked with silicone pad heaters applied to large Diesel engine oil pans, most are 120 vac 100 watts and work very well when they are plugged in while oil temperature is warm after you shutdown. They help lower starter draw and with increased cranking speed help with quicker starting
  6. 645E3B

    Poll: Sleeved and Non-Sleeved IDI Engines

    I have 126000 on my 6.9 with ATS turbo running strong with no problem, my brother has a 94 7.3 IDIT with 380000 and it’s never been apart
  7. 645E3B

    7.3 idi Turbo oil line and such fun.

    I have an ATS turbo on my IDI and the oil feed line is an AN4 from the port on the side if the engine, drivers side of the engine at the bell housing behind the oil filter
  8. 645E3B

    Help!!!! 6.9 won't start!!

    If it was running be for you did all of the work that tells you that there was a change made that is causing the problem, start with the basic things pull out the GP’s and remove the valve covers, check that valves are closing and watch for bent push rods and listen to the blow out of the glow...
  9. 645E3B

    Engine Oil Analysis In... Coolant?

    I have used lube oil sampling on large Diesel engines, one of the things that I would recommend is to send in a sample of the engine oil that you’re using to get a baseline , as oil additive packages vary and can make your sample report seam strange if you’re not sure of the starting point
  10. 645E3B

    Intermittent wipers not working

    I have a 1991 F 250 XLT with intermittent wipers Wipers work on high no low or intermittent speeds washers spray but in low speed wipers will stop in windshield and will only park if you go to high position then to off.
  11. 645E3B

    heater hoses

    I replaced the radiator on my 91 and it didn’t have the tee in the heater hose but my brother has a 94 turbo idi in a 350 and his has this set up. He was replacing hoses a few years back and was unable to find any one with this hose went to Ford and was told that it was unavailable and to remove...
  12. 645E3B

    Late 1987 6.9 wiring harness

    I am planning to update the engine wiring harness on my 6.9, it has the later style (7.3 ) GP controller. I have not been able to find a wiring harness breakdown and I don’t want to remove the one from old Sluf as I still want her running. Where is a good place to check to find a breakdown, or...
  13. 645E3B

    BILLET ALUMINUM INJECTOR CAP

    This would be a great addition to my idi
  14. 645E3B

    O’Reillys don’t buy on line

    One thing to think about when ordering parts on line from O’Reillys There customer service leaves a lot to be desired, I ordered a vacuum pump on may 29th and as of June 10th ups has lost the part. I have contacted O’Reillys about this after contacting ups you get no response from ups and...
  15. 645E3B

    Supply fuel pressure 6.9 idi

    Would like to install an electric fuel pump on a 1987 6.9 idi but I am not sure of the supply fuel pressure to the injection pump

Latest posts

Forum statistics

Threads
91,261
Posts
1,129,466
Members
24,090
Latest member
Larrymac

Members online

Total: 495 (members: 10, guests: 485)

Share this page

Top